ASNT 9712 Level II UT Exam Study Guide (2026)
Everything the ASNT 9712 Level II, Ultrasonic Testing (UT), written parts tests, topic by topic: what each section covers, the facts that come up most, and how to study it. Pair it with the free 15-question practice test.
The exam at a glance
| Questions | 110 written items over three computer-based elements: General 50, Specific 40 (Pre- and In-Service) and Instruction Preparation 20. A practical exam is also required: castings/forgings (2 parts) or welds (2 areas of interest), straight and angle beam |
|---|---|
| Time | 5 hours of written exams: General 2 hours, Specific 2 hours, Instruction Preparation 1 hour. Each practical (castings/forgings or welds) is a further 2 hours |
| Passing score | At least 70% on each written element (General, Specific and Instruction Preparation) and at least 80% on each practical specimen |
| Format | Computer-based with an on-screen scientific calculator supplied by ASNT. Codes, standards, procedures and other aids may be used only if ASNT supplies or authorizes them for that exam, and ASNT's candidate pages do not list them, so confirm with ASNT. Instruction Preparation uses multiple-choice and multiple-response items. This prep covers only the written parts, with 4-option practice items; it does not cover the hands-on practical exams |
| Certifying body | ASNT Certification Services LLC (American Society for Nondestructive Testing) |
| Test provider | Written exams at Pearson VUE test centers or ASNT Authorized Exam Centers (computer-based); practical exams only at Authorized Exam Centers |
Mind map: the whole exam on one screen
Read the complete ASNT 9712 Level II UT study notes for “UT Principles and Techniques”
Our first full set of comprehensive notes, about 14 minutes of reading: Wave modes and velocity · Refraction and critical angles · The sound beam · Instruments and standardization · Choosing a technique, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.
1. UT Principles and Techniques
First domain of the General exam outline for exams after 5 February 2027: managing and calibrating UT systems, selecting and standardizing equipment, and applying theory. It draws on the earlier topic Review of Ultrasonic Techniques. ASNT publishes no percentage weights.
Key facts
- Velocity is fixed by material and wave mode. Frequency and velocity set the wavelength, using λ = V/f.
- Steel carries longitudinal waves at about 5,920 m/s (0.233 in/µs) and shear waves at about 3,230 m/s (0.127 in/µs).
- Snell's law sets the refracted angle; the first critical angle removes the longitudinal wave and the second removes the shear wave.
- Near-field length N = D²f/(4V), where amplitude is erratic, and beam spread grows beyond it.
- Higher frequency improves resolution but increases attenuation and reduces penetration.
- Standardization uses blocks such as IIW and DSC for range and angle, and side-drilled holes or notches for sensitivity.
- A transfer correction accounts for surface and coupling differences between the block and the part.
- Decibels compare amplitudes: 6 dB is about 2 times and 20 dB is 10 times.
Flashcards
Exam tip: On calculations, write the known velocities first and keep units consistent; most errors are unit slips between inches and microseconds or meters per second.
2. Examination of Materials and Product Forms
Second domain after 5 February 2027: scan plans, component conditions, thickness measurement and examinations for inherent, manufacturing and in-service discontinuities. It absorbs the earlier topics Evaluation of Base Material Product Forms, Evaluation of Weldments, Evaluation of Bonded Structures and Discontinuity Detection. ASNT publishes no percentage weights.
Key facts
- Rolling flattens discontinuities parallel to the surface, so plate is checked mainly with straight beams.
- Forgings are examined with the beam across the grain flow, in more than one direction where the geometry allows.
- Welds are scanned with angle beams, from both sides where possible, using skip distance to cover the full volume.
- Coarse austenitic grains cause scatter and beam skewing, so lower frequency and longitudinal techniques are often better.
- Echo-to-echo thickness readings exclude surface coatings from the measurement.
- Velocity falls with temperature, so a gauge set at room temperature reads high on hot steel.
- Bonded structures are examined for disbonds and voids by pulse echo, through transmission or resonance.
Flashcards
Exam tip: Match beam direction to the flaw orientation the process produces. Rolling, forging and welding each favor a different scan.
3. UT Data Collection, Interpretation and Reporting
Third domain after 5 February 2027: identifying irregularities, verifying data quality, deciding relevant versus non-relevant, characterizing planar and volumetric indications, evaluating against acceptance criteria and documenting results. It draws on the earlier topic General Evaluation. ASNT publishes no percentage weights.
Key facts
- Decide first whether an echo comes from the part, the geometry or the instrument.
- Planar reflectors respond strongly at one angle and fall off sharply as the unit rotates or orbits.
- Rounded, volumetric reflectors respond over a wide range of angles.
- Geometric echoes such as the root and counterbore often plot at a known position.
- The 6 dB drop finds the edges of a reflector larger than the beam, but overstates a small reflector.
- The 20 dB drop method uses the beam's edge rather than the center.
- Reports record the procedure, equipment, calibration, coverage, indications and disposition.
Flashcards
Exam tip: Plot the indication before you call it. A position that matches geometry often answers the question without needing the amplitude.
Test yourself on these topics
Take the free 15-question ASNT 9712 Level II UT test, then save your results to unlock your Readiness Score and the mistakes bank.
4. UT Training, Certification and Safety
Fourth domain after 5 February 2027: maintaining credentials, complying with safety requirements, providing on-the-job training to other technicians and administering UT tests. ASNT publishes no percentage weights.
Key facts
- ASNT 9712 Level II certificates must be renewed every five years, before the expiration date.
- Initial UT certification requires 18 days of training and 180 days of experience.
Flashcards
Exam tip: Know the retake ladder in order: 30 days, then 90 days with training, then six months as a new candidate.
5. Specific Exam: Pre- and In-Service Applications
A separate 40-item, 2-hour computer-based exam. ASNT's page lists Codes, Applications and Techniques for the shared Pre- and In-Service sector without naming documents or publishing percentage weights, so confirm any code edition or supplied procedure with ASNT. ASME Section V Article 4 and Section VIII Appendix 12 are common references.
Key facts
- Article 4 requires calibration confirmation at the start and end of each examination and at the intervals it sets.
- An amplitude reduction over 20% or 2 dB voids the examination since the last valid check.
Flashcards
Exam tip: Read whether the amplitude went up or down at the calibration check. Direction decides whether you re-scan or only re-evaluate.
6. Instruction Preparation
A separate 20-item, 1-hour computer-based element with multiple-choice and multiple-response items, testing the creation of a written UT instruction. Weighting: foreword 5%, personnel 5%, equipment and media 5%, product 10%, test conditions 10%, detailed instructions 40%, recording and classifying results 20%, reporting 5%.
Key facts
- An NDT instruction describes the exact steps for carrying out a test according to a standard or procedure.
- Detailed instructions, including settings, carry the largest share at 40%.
Flashcards
Exam tip: Check every setting a Level I would need against the instruction. If one is missing or vague, the instruction is incomplete.
How to pass
- Check your exam date against 5 February 2027. Earlier General exams use the six-topic outline, including bonded structures; later ones use four job-task domains.
- Each written element has its own 70% minimum, so a strong General score can't offset a weak Instruction Preparation result.
- Instruction Preparation is 20 items in 1 hour, and the detailed test instructions carry 40% of its weighting. Practice writing frequency, angle, reference level and scan coverage as stated values.
- Move quickly on the arithmetic: Snell's law, dB ratios, and time-base positions. ASNT supplies the calculator, so review its guide before test day.
Frequently asked questions
How long should I study for the ASNT 9712 Level II UT exam?
Most working candidates need 4 to 8 weeks at 45 to 60 minutes a day. Book your exam once your Readiness Score has stayed at 80 or higher for about a week.
Can I take the ASNT 9712 Level II UT exam online?
No. ASNT NDT Level III exams are taken in person, on a computer, at Pearson VUE test centers or ASNT Authorized Exam Centers. Format: computer-based with an on-screen scientific calculator supplied by asnt. codes, standards, procedures and other aids may be used only if asnt supplies or authorizes them for that exam, and asnt's candidate pages do not list them, so confirm with asnt. instruction preparation uses multiple-choice and multiple-response items. this prep covers only the written parts, with 4-option practice items; it does not cover the hands-on practical exams. Check ASNT's current exam information for the rules.
What score do I need to pass the ASNT 9712 Level II UT exam?
At least 70% on each written element (General, Specific and Instruction Preparation) and at least 80% on each practical specimen. The exam has 110 written items over three computer-based elements: general 50, specific 40 (pre- and in-service) and instruction preparation 20. a practical exam is also required: castings/forgings (2 parts) or welds (2 areas of interest), straight and angle beam and a time limit of 5 hours of written exams: general 2 hours, specific 2 hours, instruction preparation 1 hour. each practical (castings/forgings or welds) is a further 2 hours.
What are the most tested topics?
The outline covers ut principles and techniques, examination of materials and product forms, ut data collection, interpretation and reporting, ut training, certification and safety, specific exam: pre- and in-service applications, instruction preparation. Use the free practice test to see which ones you need most.
The premium ASNT 9712 Level II UT study path
Premium ASNT 9712 Level II UT prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.
Your step-by-step study path
- 1UT Principles and Techniques10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Notes free with an account
- 2Examination of Materials and Product Forms10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Premium
- 3UT Data Collection, Interpretation and Reporting10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Premium
- 4UT Training, Certification and Safety10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Premium
- 5Specific Exam: Pre- and In-Service Applications10 key notes, 130 flashcards, then 500 practice questions in 20 sets of 25Premium
- 6Instruction Preparation10 key notes, 130 flashcards, then 500 practice questions in 20 sets of 25Premium
- Final step: 6 full mock exams110 questions each, timed like test day. Pass them, then book your exam.Premium
Get every note, flashcard and question
Premium Monthly
- One ASNT Level III exam of your choice: Basic, UT, RT or MT
- 3,000 practice questions + 6 full mock exams per exam
- 800 flashcards + 60 key notes per exam, by topic, plus mind maps
- Spaced repetition + mistakes bank
- Readiness Score & detailed reports
- Video lessons as they release
- Content updates during your access
- 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
- Pass Guarantee: complete the prep, pass or 100% back
Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.
Premium Yearly
- One ASNT Level III exam of your choice: Basic, UT, RT or MT
- 3,000 practice questions + 6 full mock exams per exam
- 800 flashcards + 60 key notes per exam, by topic, plus mind maps
- Spaced repetition + mistakes bank
- Readiness Score & detailed reports
- Video lessons as they release
- Content updates during your access
- 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
- Pass Guarantee: complete the prep, pass or 100% back
Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.
Summarized from ASNT's official candidate information and the rules cited, checked October 2026. Confirm current requirements with ASNT Certification Services LLC (American Society for Nondestructive Testing).