Try the full study dashboard free, no signup: practice, flashcards and your Exam Readiness Score. Open it →
Home / Practice tests / ASNT 9712 Level II MT
ASNT · Last updated November 2026

ASNT 9712 Level II, Magnetic Particle Testing (MT), written parts: free practice test

ASNT's ISO 9712-based Level II certification for magnetic particle testing, requiring 5 days of training, 60 days of experience and four examination elements. The General exam moves to a revised five-domain MT outline for exams after 15 December 2026, and this prep follows that outline while still mapping to the earlier topics. This prep covers only the three written elements, not the practical exam.

Watch the free 4:24 video lesson: the key ASNT 9712 Level II MT concepts →

Premium: 3,000 practice questions, 6 full mock exams, 800 flashcards and 60 comprehensive key notes, topic by topic. See the study path ·

Or open the free ASNT 9712 Level II MT study dashboard: flashcards, notes and your Readiness Score, no signup →

About the ASNT 9712 Level II MT exam

ASNT's ISO 9712-based Level II certification for magnetic particle testing, requiring 5 days of training, 60 days of experience and four examination elements. The General exam moves to a revised five-domain MT outline for exams after 15 December 2026, and this prep follows that outline while still mapping to the earlier topics. This prep covers only the three written elements, not the practical exam.

What's on the exam

ASNT 9712 Level II MT
MT Principles and Theory
7 key facts
Use and Care of MT Equipment and Accessories
8 key facts
MT Techniques and Demagnetization
7 key facts
Interpreting, Evaluating and Documenting Results
6 key facts
Codes, Standards, Specifications and Procedures
6 key facts
Specific Exam: Pre- and In-Service Applications
6 key facts
Instruction Preparation
6 key facts

Each branch is a topic in the official outline. Members see every key fact on the full mind map. Read the free study guide →

How to pass the ASNT 9712 Level II MT exam

  • Check your exam date against 15 December 2026. Earlier General exams use the ten-topic outline; later ones use the five job-task domains, including QQIs, Ketos rings and field meters.
  • Each written element has its own 70% minimum, so a strong General score can't offset a weak Instruction Preparation result.
  • Instruction Preparation is 20 items in 1 hour, and the detailed test instructions carry 40% of its weighting. Practice writing settings that a Level I could follow with no guesswork.
  • Know the current formulas and their limits cold: direct contact, prods by thickness, the L/D cap on the coil equation and offset central conductor coverage.

Save your results and get your Readiness Score

Create a free account after the test: your score by topic, a mistakes bank, the complete study notes for the first topic, flashcards and the NDT Level III Formula Sheet.

Take the test first

What's in the premium ASNT 9712 Level II MT prep

Premium ASNT 9712 Level II MT prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.

3,000practice questions, every answer explained
6full-length mock exams, 110 questions each, timed
800flashcards with spaced repetition, sorted by topic
60comprehensive key notes across 7 topics

Your step-by-step study path

  1. 1
    MT Principles and Theory9 key notes, 115 flashcards, then 450 practice questions in 18 sets of 25
    Notes free with an account
  2. 2
    Use and Care of MT Equipment and Accessories9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  3. 3
    MT Techniques and Demagnetization9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  4. 4
    Interpreting, Evaluating and Documenting Results9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  5. 5
    Codes, Standards, Specifications and Procedures8 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  6. 6
    Specific Exam: Pre- and In-Service Applications8 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  7. 7
    Instruction Preparation8 key notes, 110 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  8. Final step: 6 full mock exams110 questions each, timed like test day. Pass them, then book your exam.
    Premium
Free with an account

Read the complete ASNT 9712 Level II MT study notes for “MT Principles and Theory”

Our first full set of comprehensive notes, about 14 minutes of reading: How MT works · Field type and direction · Choosing the magnetizing current · Selecting particles · Material properties and oversight, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.

Open the free dashboard

Study tools included

3,000 practice questions

3,000 exam-style questions per exam, organized topic by topic in sets of 25. Every answer explained, with the rule it comes from.

6 full mock exams

6 full-length timed mock exams per exam, with real question counts and time limits, so test day feels like practice day.

Exam Readiness Score

One 0 to 100 number that tells you when you're ready to book. Reach 80 and you're covered by our Pass Guarantee.

800 flashcards + spaced repetition

800 flashcards per exam, in a deck for each topic, that come back right before you'd forget them. Five minutes a day keeps every number fresh.

60 comprehensive key notes

60 key notes per exam, split across its topics and each explained in full: the concepts, worked exam examples, the traps examiners use and a quick recap. Your first set is free with an account.

Mind maps

See the whole exam on one screen: every topic and the facts under it.

Sample questions with answers

These are the questions in the free test above, with answers. Try the test first. You'll learn more by getting some wrong.

1. A hollow steel bushing must be examined for longitudinal cracks on its inside surface. Which setup is the best choice?
Answer: A central conductor threaded through the bore. Longitudinal cracks need a circular field, and a central conductor creates that field at the bore. Current passing through the bushing itself creates no useful field at the inside surface, even though it does at the outside. A coil gives a longitudinal field, which runs parallel to these cracks.
2. A bench unit will be used to examine ground bearing races for very fine surface cracks. Which particle type gives the best sensitivity?
Answer: Wet fluorescent particles in a bath. Fine wet particles are mobile on smooth surfaces and fluorescent dye gives a high-contrast indication, so wet fluorescent particles suit fine surface cracks on a bench unit. Dry powder is coarser and better suited to rough field surfaces and to subsurface work with half-wave current.
3. Yoke legs straddle a butt weld, so that the line between the poles crosses the weld at 90°. Which discontinuities will this setup detect best?
Answer: Cracks parallel to the weld axis. A yoke's field runs from pole to pole, here across the weld, and flaws show best when they lie at right angles to the field. Cracks parallel to the weld are therefore favored. A second scan with the yoke turned about 90° is needed for transverse cracks.
4. An AC yoke lifts its 10 lb test weight at a 4 in pole spacing, but the job needs an 8 in spacing. What should be done before using the wider spacing?
Answer: Repeat the lift test with the legs set at the 8 in spacing. ASME Section V Article 7 ties the yoke lift requirement to the maximum pole spacing that will be used, since lifting power falls as the legs move apart. A pass at 4 in proves nothing about 8 in. DC and permanent magnet yokes have their own, higher requirement of 40 lb.
5. A settling test on a wet fluorescent bath shows 0.8 mL of particles per 100 mL after the required settling time. What should be done?
Answer: Add vehicle to dilute the bath, then retest it. Wet fluorescent baths normally run at 0.1 to 0.4 mL per 100 mL, so 0.8 mL is too concentrated and can raise background and mask fine indications. Dilute with clean vehicle and retest. The higher 1.2 to 2.4 mL range belongs to visible baths, a mix-up often seen in this test.
6. A tangential Hall-effect probe reads 12 G at the part surface during magnetization, and the ASME Section V Article 7 procedure uses this reading to prove field adequacy. What does it show?
Answer: Inadequate, so raise the current and recheck. A tangential field of at least 30 G (2.4 kA/m) is the Article 7 adequacy value with a Hall-effect probe, so 12 G is too weak. Raise the current and measure again. Lowering the current makes the shortfall worse, and a field indicator showing a direction alone does not prove strength.
7. A technician calculates 2,250 ampere-turns for a 30 in long, 1.5 in diameter bar lying near the wall of a low fill-factor coil, using the ASME Section V Article 7 equation. What is the correct value?
Answer: 3,000 ampere-turns. L/D is 20, but Article 7 limits it to a maximum of 15 in this equation, so NI = 45,000 ÷ 15 = 3,000 ampere-turns (±10%). The 2,250 figure comes from using the uncapped L/D of 20, which leaves the part under-magnetized. On a 6-turn coil, 3,000 ampere-turns would mean 500 A.
8. Under ASME Section V Article 7, prods will be used on a 1/2 in thick plate with the current set to 500 A. Which prod spacing keeps that current in the required range?
Answer: 5 in. For material under 3/4 in thick, Article 7 uses 90 to 110 A per inch of prod spacing. At 5 in the range is 450 to 550 A, which includes 500 A; 4 in tops out at 440 A and 6 in starts at 540 A. At 3/4 in and thicker, use 100 to 125 A per inch.
9. A shaft still shows residual field after AC coil demagnetization because the operator switched the coil off with the shaft inside it. What is the correct fix?
Answer: Keep AC on and withdraw the shaft well clear of the coil. AC coil demagnetization works by reversing the field while its strength falls as the part moves away from the coil. The part must leave the field fully before the current stops. Switching off inside the coil can leave a strong residual field, so the sequence must be corrected and the result verified.
10. A soft, fuzzy line appears on a magnetized part at a point where another magnetized part had touched it. After demagnetizing and reprocessing, it is gone. What was it most likely to be?
Answer: Magnetic writing, a false indication. Magnetic writing is caused by contact with another magnetized object, and it disappears after demagnetization and reprocessing. Real discontinuities reappear because the flaw remains. It is a false indication, so note it and do not report it as a discontinuity once it has been properly confirmed.
11. A hardened, ground surface shows a pattern of shallow, jagged lines running roughly at right angles to the grinding direction. What are these indications most likely to be?
Answer: Grinding cracks. Grinding cracks are shallow, often appear as a pattern or checks and tend to run across the grinding direction, caused by local overheating of hardened surfaces. Seams and stringers follow the rolling direction of the product, and laps come from forging and do not form a grinding-related pattern.
12. Under ASME Section VIII Division 1, Appendix 6, a weld shows an MT indication 1/4 in long and 1/16 in wide. How is it classified and dispositioned?
Answer: Relevant and linear, so reject it. An indication is relevant when its major dimension exceeds 1/16 in, and linear when its length is more than three times its width. At 1/4 in by 1/16 in the ratio is 4, so this is a relevant linear indication, which Appendix 6 does not accept. Relevance goes by length, not width.
13. A 1 in diameter central conductor is offset against the wall of a ring with a 24 in inner circumference. Using ASME Section V Article 7 coverage rules with about 10% overlap, how many positions are needed?
Answer: 7. Article 7 takes the effective region as four conductor diameters, here 4 in along the circumference. A 10% overlap leaves 3.6 in of new coverage per position, and 24 ÷ 3.6 = 6.7, which rounds up to 7. Six positions would only work with no overlap at all.
14. A long butt weld is scanned once with a yoke, with the legs straddling the weld. What does ASME Section V Article 7 require next?
Answer: Rescan with the field about 90° to the first scan. Article 7 requires at least two separate examinations of each area, with the lines of flux in the second roughly perpendicular to the first. One orientation can miss flaws running parallel to the field. Slower scanning or more particles does not change the field direction, so it does not fix the gap.
15. A Level II is writing an instruction for a Level I who will perform yoke MT on a weld. Which line is suitable to include?
Answer: Set pole spacing to 4 in and confirm the 10 lb lift. An instruction must let a Level I act without judgment calls, so settings have to be stated. The detailed test instructions carry 40% of the Instruction Preparation weighting in the ASNT 9712 Program Document. Terms like enough, appropriate and suitable leave the setup to the operator.

Get the full ASNT 9712 Level II MT prep

Most popular · cancel anytime

Premium Monthly

$147/month
per exam
About $4.83 a day · less than a retake fee, for the certification that lets you approve procedures and certify technicians
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.

Best value · 3 months free

Premium Yearly

$1,323/year
per exam
Pay for 9 months, get 12. Save $441 against paying monthly.
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.

Pass Guarantee. Complete the full prep, sit your exam within 60 days, and if you don't pass we refund 100% of your subscription payments. See the requirements
Secure checkout by Stripe Card, Apple Pay, Google Pay Pass Guarantee

ASNT 9712 Level II MT exam FAQ

How many questions are on the ASNT 9712 Level II MT exam?

110 written items over three computer-based elements: General 50, Specific 40 (Pre- and In-Service) and Instruction Preparation 20. A practical exam (bench or yoke, 2 pieces) is also required, with a time limit of 5 hours of written exams: general 2 hours, specific 2 hours, instruction preparation 1 hour. each practical (bench or yoke) is a further 1 hour. Format: computer-based with an on-screen calculator. asnt's candidate pages do not state the reference-material rules, so confirm them with asnt. instruction preparation uses multiple-choice and multiple-response items. this prep covers only the written parts, with 4-option practice items; it does not cover the hands-on practical exam.

What is the passing score for ASNT 9712 Level II MT?

At least 70% on each written element (General, Specific and Instruction Preparation) and at least 80% on each practical specimen.

How much does the ASNT 9712 Level II MT exam cost?

US$1,270 for ASNT members, US$1,345 for nonmembers (single technique); all techniques US$1,620 / US$1,715. Retakes: General or Specific US$415 / US$465, Instruction Preparation US$400 / US$455, practical US$500 / US$590. ASNT fees differ for members and nonmembers and can change, so confirm on the ASNT certification website before you apply.

Which languages is the ASNT 9712 Level II MT exam offered in?

English only (an online NDT terminology dictionary covers Korean, Mandarin, Spanish, UK English and Arabic).

Where do I take the ASNT 9712 Level II MT exam?

Written exams at Pearson VUE test centers or ASNT Authorized Exam Centers (computer-based); practical exams only at Authorized Exam Centers.

Is this ASNT 9712 Level II MT practice test free?

Yes. The 15-question practice test on this page is free, with an explanation for every answer and no signup. A free account also unlocks the complete study notes for the first topic. The full ASNT 9712 Level II MT prep is Premium at $147 a month for this exam.

What's in the premium ASNT 9712 Level II MT prep?

3,000 practice questions organized topic by topic (MT Principles and Theory: 450; Use and Care of MT Equipment and Accessories: 425; MT Techniques and Demagnetization: 425; Interpreting, Evaluating and Documenting Results: 425; Codes, Standards, Specifications and Procedures: 425; Specific Exam: Pre- and In-Service Applications: 425; Instruction Preparation: 425), 6 full-length timed mock exams of 110 questions, 800 flashcards and 60 comprehensive key notes split across all 7 topics, plus a mistakes bank and the Readiness Score.

Related practice tests

Exam details are summarized from the official candidate information available in October 2026. ASNT changes formats and fees, so confirm with ASNT Certification Services LLC (American Society for Nondestructive Testing) before you book. NDTLevel3Exam is not affiliated with ASNT or Pearson VUE.

Start the free test