ASNT 9712 Level III Ultrasonic Testing (UT), written parts: free practice test
ASNT's ISO 9712-based Level III certification in ultrasonic testing. Candidates need 18 days of Level II and 5 days of Level III training and 270 to 540 days of experience, then pass the Basic, Basic Supplemental, UT Method and Procedure Preparation exams and the straight and angle beam practicals. The UT Method exam follows a revised five-domain outline for exams after 15 July 2026; this prep covers only the written parts, not the practicals.
Watch the free 4:11 video lesson: the key ASNT 9712 Level III UT concepts →
Premium: 3,000 practice questions, 6 full mock exams, 800 flashcards and 60 comprehensive key notes, topic by topic. See the study path ·
- Lesson 2: Wave modes and velocities in common materialsLongitudinal, shear, Rayleigh and Lamb waves, wavelength sums and which mode suits which job.
- Lesson 3: Acoustic impedance and interface reflectionImpedance mismatch, reflection and transmission coefficients, and why couplant choice matters.
- Lesson 4: Snell's law, mode conversion and critical anglesRefraction sums for contact and immersion, first and second critical angles, wedge design.
- Lesson 5: Beam geometry: near field, spread and focusingNear field length, beam spread at minus six and minus twenty decibels, immersion focal shift.
- Lesson 6: Attenuation, decibels and the gain equationScattering and absorption, decibel arithmetic, and attenuation measurement from back-wall echoes.
- Lesson 7: Evaluating new UT technologies and proceduresHow a Level Three judges PAUT, TOFD and full matrix capture for a given application.
- Lesson 8: Reference standards and transfer correctionDesigning acoustically similar blocks, side-drilled holes, notches and documented transfer corrections.
- Lesson 9: Plate, forgings and castings by product formExpected flaws, grain flow, scan directions and frequency choice for each product form.
- Lesson 10: Pipe, tube and curved surface examinationsCircumferential and axial scans, ID over OD limits and contoured wedge requirements.
- Lesson 11: Austenitic welds and coarse-grained materialsBeam skewing, grain noise, refracted longitudinal waves and dual-element probe choices.
- Lesson 12: Selecting probes, cables, couplants and instrumentsMatching frequency, element size, angle and damping to thickness, geometry and flaw type.
- Lesson 13: Interpreting codes: ASME Section V Article 4Calibration, scanning sensitivity, overlap, calibration checks and what the referencing code decides.
- Lesson 14: DAC, TCG and sizing techniques comparedSix decibel drop, twenty decibel drop and tip diffraction sizing, and when each misleads.
- Lesson 15: Characterizing planar and volumetric discontinuitiesEcho dynamics, angle sensitivity and pattern clues that separate cracks from porosity and slag.
- Lesson 16: Reading PAUT and TOFD dataSectorial scans, angle-corrected gain, lateral waves and TOFD depth calculations.
- Lesson 17: Writing reports that can be repeatedProcedure, equipment, calibration, coverage, indications and dispositions a Level Three must record.
- Lesson 18: Building UT training and examinationsTraining content, question writing, practical specimens and proctoring under ASNT 9712.
- Lesson 19: ASNT 9712 training, experience and retake rulesTraining days, experience routes, retake intervals and how they differ from SNT-TC-1A.
- Lesson 20: Technical oversight of UT techniciansAuditing performance, spotting refresher needs and managing certification documentation timelines.
- Lesson 21: Instrument linearity and transducer verificationScreen height and amplitude control linearity, beam angle, exit point and resolution checks.
- Lesson 22: Running a UT equipment maintenance programEquipment registers, calibration due dates, repairs and handling results from a failed instrument.
- Lesson 23: Procedure Preparation exam: building the procedureSection by section drafting to a supplied standard, prioritising technique, setup and acceptance criteria.
Keep going after the free lesson. Every topic gets its own lesson, plus the full question bank, timed simulations and study tools.
About the ASNT 9712 Level III UT exam
ASNT's ISO 9712-based Level III certification in ultrasonic testing. Candidates need 18 days of Level II and 5 days of Level III training and 270 to 540 days of experience, then pass the Basic, Basic Supplemental, UT Method and Procedure Preparation exams and the straight and angle beam practicals. The UT Method exam follows a revised five-domain outline for exams after 15 July 2026; this prep covers only the written parts, not the practicals.
What's on the exam
Each branch is a topic in the official outline. Members see every key fact on the full mind map. Read the free study guide →
How to pass the ASNT 9712 Level III UT exam
- Check which exams your approval letter lists. A valid Level III holder is exempt from the Basic exam, and ASNT's fee table charges current ASNT NDT Level III holders only for Basic Supplemental, Procedure Preparation and the practicals.
- The UT Method outline for exams after 15 July 2026 has five domains: principles and theory, materials and product forms, data collection and interpretation, training and certification programs, and equipment. Study the Level III tasks, such as designing reference standards and managing equipment, not just the physics.
- Keep the calculator skills sharp: Snell's law and critical angles, focusing in immersion, TOFD depth, pipe geometry limits and decibel ratios all fit the 135 items in 4 hours.
- In Procedure Preparation, performance of the test carries 40% of the marks and materials and equipment 20%. State the calibration block, reference reflector, scanning sensitivity and recording level exactly as the supplied standard requires.
Save your results and get your Readiness Score
Create a free account after the test: your score by topic, a mistakes bank, the complete study notes for the first topic, flashcards and the NDT Level III Formula Sheet.
What's in the premium ASNT 9712 Level III UT prep
Premium ASNT 9712 Level III UT prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.
Your step-by-step study path
- 1UT Principles and Theory8 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25Notes free with an account
- 2UT Materials and Product Forms8 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25Premium
- 3UT Data Collection, Interpretation and Reporting8 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25Premium
- 4UT Training and Certification Programs8 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25Premium
- 5UT Equipment7 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25Premium
- 6Procedure Preparation7 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25Premium
- 7Basic Exam: NDT Methods, Materials and Programs7 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25Premium
- 8Basic Supplemental: ASNT 9712 Certification System7 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25Premium
- Final step: 6 full mock exams135 questions each, timed like test day. Pass them, then book your exam.Premium
Read the complete ASNT 9712 Level III UT study notes for “UT Principles and Theory”
Our first full set of comprehensive notes, about 15 minutes of reading: Waves and velocities · Refraction and critical angles · Beam geometry · Amplitude and impedance, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.
Study tools included
3,000 practice questions
3,000 exam-style questions per exam, organized topic by topic in sets of 25. Every answer explained, with the rule it comes from.
6 full mock exams
6 full-length timed mock exams per exam, with real question counts and time limits, so test day feels like practice day.
Exam Readiness Score
One 0 to 100 number that tells you when you're ready to book. Reach 80 and you're covered by our Pass Guarantee.
800 flashcards + spaced repetition
800 flashcards per exam, in a deck for each topic, that come back right before you'd forget them. Five minutes a day keeps every number fresh.
60 comprehensive key notes
60 key notes per exam, split across its topics and each explained in full: the concepts, worked exam examples, the traps examiners use and a quick recap. Your first set is free with an account.
Mind maps
See the whole exam on one screen: every topic and the facts under it.
Sample questions with answers
These are the questions in the free test above, with answers. Try the test first. You'll learn more by getting some wrong.
1. An acrylic wedge (longitudinal velocity 2,730 m/s) is used on steel (shear velocity 3,230 m/s). Above what incident angle is there no shear wave in the steel?
2. A focused immersion search unit has a focal length of 75 mm in water. It is set at a 50 mm water path over a steel part. About how deep in the steel does the beam focus?
3. A 2 MHz surface (Rayleigh) wave is used on steel to look for shallow surface cracks. Rayleigh velocity is about 0.92 of the shear velocity. To about what depth is the wave sensitive?
4. A circumferential shear-wave scan for longitudinal inside-surface cracks is planned on a seamless pipe with 10.0 in outside diameter and 2.0 in wall. What is the largest refracted angle that still reaches the inside surface?
5. A Level III must design a reference block for straight-beam testing of nickel-alloy forgings. A technician suggests using an existing carbon steel block with the same hole sizes. What is the main objection?
6. A TOFD setup uses an 80 mm probe center separation on steel. A diffracted tip signal arrives at a total sound path of 100 mm. Assuming the tip lies midway between the probes and ignoring wedge delay, how deep is it?
7. In a phased array sectorial scan from 40° to 70°, the same side-drilled hole gives different amplitudes at different angles. What does angle-corrected gain (ACG) do?
8. Reviewing an ASME Section V Article 4 weld examination report, you see that scanning was done at the primary reference level gain. What is the finding?
9. A Level III is planning training for a direct-access candidate for ASNT 9712 Level II UT (no prior Level I). What minimum training and experience does the ASNT 9712 Program Document require?
10. During a screen height linearity check under ASME Section V Article 4, the larger of two hole echoes is set to 80% full screen height and the smaller reads 33%. What is the finding?
11. A periodic probe check shows that a contact transducer's echo now has many more cycles than at acceptance, and near-surface resolution has been lost. What is the most likely cause?
12. In the Procedure Preparation exam you are asked to critique an existing UT procedure. It names 45° and 60° probes and a scan pattern but gives no calibration block, reference reflector or scanning sensitivity. What is the most serious omission?
13. With 30 minutes left in the Procedure Preparation exam, your procedure still lacks several sections. Based on ASNT's weighting table, which should you complete first?
14. A Level III must confirm by destructive testing whether a UT indication in a production weld coupon is lack of sidewall fusion or slag. Which test shows this most directly?
15. An ASNT 9712 Level III UT holder applies for renewal. Their near-vision test was 14 months ago and their color vision test 3 years ago. What does the program document require?
Get the full ASNT 9712 Level III UT prep
Premium Monthly
- One ASNT Level III exam of your choice: Basic, UT, RT or MT
- 3,000 practice questions + 6 full mock exams per exam
- 800 flashcards + 60 key notes per exam, by topic, plus mind maps
- Spaced repetition + mistakes bank
- Readiness Score & detailed reports
- Video lessons as they release
- Content updates during your access
- 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
- Pass Guarantee: complete the prep, pass or 100% back
Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.
Premium Yearly
- One ASNT Level III exam of your choice: Basic, UT, RT or MT
- 3,000 practice questions + 6 full mock exams per exam
- 800 flashcards + 60 key notes per exam, by topic, plus mind maps
- Spaced repetition + mistakes bank
- Readiness Score & detailed reports
- Video lessons as they release
- Content updates during your access
- 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
- Pass Guarantee: complete the prep, pass or 100% back
Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.
ASNT 9712 Level III UT exam FAQ
How many questions are on the ASNT 9712 Level III UT exam?
Four computer-based written elements: Basic 135 items, Basic Supplemental 55 items, UT Method 135 items, and Procedure Preparation (write one complete UT procedure to a supplied standard). Practical exams (weld, and casting/forging, straight and angle beam) are also required, with a time limit of basic 4 hours, basic supplemental 2 hours, ut method 4 hours, procedure preparation 4 hours. Format: computer-based with an on-screen calculator. codes, standards and other aids are allowed only if asnt supplies or authorizes them; the standard for procedure preparation is supplied. procedure preparation is a written procedure, not multiple choice, graded on asnt's weighting table. this prep covers only the written knowledge parts, with 4-option practice items; it does not cover the hands-on practical exams.
What is the passing score for ASNT 9712 Level III UT?
At least 70% on each written element and at least 80% on each practical exam (ASNT 9712 Program Document Rev 02, section 8).
How much does the ASNT 9712 Level III UT exam cost?
US$1,460 for ASNT members, US$1,655 for nonmembers (Procedure Preparation and practical exams; current ASNT NDT Level III holders add the US$120 Basic Supplemental fee). Applicants without ASNT NDT Level III add US$1,210 / US$1,370 for the UT Method, Basic and Basic Supplemental exams. Retakes: Method US$475 / US$555, Procedure Preparation US$560 / US$655, each practical US$500 / US$590. ASNT fees differ for members and nonmembers and can change, so confirm on the ASNT certification website before you apply.
Which languages is the ASNT 9712 Level III UT exam offered in?
English only (an online NDT terminology dictionary covers Korean, Mandarin, Spanish, UK English and Arabic).
Where do I take the ASNT 9712 Level III UT exam?
Written exams at Pearson VUE test centers or ASNT Authorized Exam Centers (computer-based); practical exams only at Authorized Exam Centers.
Is this ASNT 9712 Level III UT practice test free?
Yes. The 15-question practice test on this page is free, with an explanation for every answer and no signup. A free account also unlocks the complete study notes for the first topic. The full ASNT 9712 Level III UT prep is Premium at $147 a month for this exam.
What's in the premium ASNT 9712 Level III UT prep?
3,000 practice questions organized topic by topic (UT Principles and Theory: 375; UT Materials and Product Forms: 375; UT Data Collection, Interpretation and Reporting: 375; UT Training and Certification Programs: 375; UT Equipment: 375; Procedure Preparation: 375; Basic Exam: NDT Methods, Materials and Programs: 375; Basic Supplemental: ASNT 9712 Certification System: 375), 6 full-length timed mock exams of 135 questions, 800 flashcards and 60 comprehensive key notes split across all 8 topics, plus a mistakes bank and the Readiness Score.
Related practice tests
ASNT NDT Level II, Liquid Penetrant Testing (PT)
ASNT's third-party written certification for liquid penetrant technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector.
ASNT NDT Level II, Radiographic Testing (RT)
ASNT's third-party written certification for radiographic technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector.
ASNT NDT Level II, Ultrasonic Testing (UT)
ASNT's third-party written certification for ultrasonic technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector.
Exam details are summarized from the official candidate information available in October 2026. ASNT changes formats and fees, so confirm with ASNT Certification Services LLC (American Society for Nondestructive Testing) before you book. NDTLevel3Exam is not affiliated with ASNT or Pearson VUE.