ASNT NDT Level II, Liquid Penetrant Testing (PT): free practice test
ASNT's third-party written certification for liquid penetrant technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector. Applicants document 30 days of PT experience, 58 days of total NDT experience and 2 days of training. This prep covers only the written exams; the visual acuity, practical and any job-specific exams are given by your employer.
Watch the free 4:42 video lesson: the key ASNT NDT Level II PT concepts →
Premium: 3,000 practice questions, 6 full mock exams, 800 flashcards and 60 comprehensive key notes, topic by topic. See the study path ·
- Lesson 2: Capillary action, surface tension and contact angleThe physics of entry and bleed-out, and how each property shifts sensitivity.
- Lesson 3: What PT can and cannot detectSurface-open limits, porous materials, and comparing PT with MT and VT.
- Lesson 4: Developer action and indication formationReverse capillary action, contrast backgrounds and why indications look wider than flaws.
- Lesson 5: Penetrant types and sensitivity levelsType I and II, AMS 2644 sensitivity levels, and what drives sensitivity.
- Lesson 6: Methods A to D in depthWater-washable, lipophilic, solvent-removable and hydrophilic removal compared step by step.
- Lesson 7: Developer forms a to fDry, water-soluble, suspendible and nonaqueous developers, and where each fits.
- Lesson 8: Contaminant control for nickel, stainless and titaniumSulfur and halogen limits, certification of materials, and why they matter.
- Lesson 9: Choosing a process for the partSurface finish, volume, location and sensitivity used to eliminate wrong options.
- Lesson 10: Material families and compatibilityWhy penetrant, remover and developer must come from one qualified family.
- Lesson 11: Pre-cleaning methods and surface preparationDegreasing, etching, mechanical cleaning risks and the adjacent area rule.
- Lesson 12: Penetrant application and dwell timesTable T-672 values, temperature limits and comparator block qualification.
- Lesson 13: Excess removal and emulsification timingRinse pressure and temperature, over and under emulsification, solvent wiping.
- Lesson 14: Drying, developing and developing timeDrying limits, coating thickness and when the developing clock starts.
- Lesson 15: Viewing conditions for visible and fluorescent PTWhite light, UV-A intensity, ambient light, warm-up and dark adaptation.
- Lesson 16: Reading crack, porosity, lap and cold shut indicationsHow each discontinuity appears and how to tell them apart.
- Lesson 17: Casting, forging and weld discontinuitiesHot tears, shrinkage, laps and weld flaws linked to manufacturing process.
- Lesson 18: Relevant, nonrelevant and false indicationsA step-by-step method for classifying every indication before acceptance.
- Lesson 19: Post-cleaning, records and reportingRemoving residues, documenting results and what a Level II report includes.
- Lesson 20: Written procedures and essential variablesProcedure content, requalification triggers and Level II versus Level III duties.
- Lesson 21: Equipment checks and process controlTest panels, light meters, penetrant and developer checks and their frequency.
- Lesson 22: ASME Section V Article 6 walkthroughThe paragraphs the Specific exam draws on, read and applied in order.
- Lesson 23: Acceptance criteria and Specific exam practiceAppendix 8 linear and rounded rules worked through realistic sector scenarios.
Keep going after the free lesson. Every topic gets its own lesson, plus the full question bank, timed simulations and study tools.
About the ASNT NDT Level II PT exam
ASNT's third-party written certification for liquid penetrant technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector. Applicants document 30 days of PT experience, 58 days of total NDT experience and 2 days of training. This prep covers only the written exams; the visual acuity, practical and any job-specific exams are given by your employer.
What's on the exam
Each branch is a topic in the official outline. Members see every key fact on the full mind map. Read the free study guide →
How to pass the ASNT NDT Level II PT exam
- The General exam allows 2.4 minutes per item and the Specific exam 3 minutes. PT has little arithmetic, so spend the spare time on process-order and acceptance items, where one word changes the answer.
- ASNT publishes no cut score for this exam. The 70% per exam and 80% composite figures often quoted come from employer programs under SNT-TC-1A, so treat 80% on each exam as your practice target.
- ASNT's public page does not name the codes behind the Specific exam. ASME Section V Article 6 and ASTM E165 are the usual references for pressure equipment and general industry work, so learn how their limits are applied.
- After a failed exam you must reapply and wait 30 days. A passed General result stays valid for 5 years, but a passed Specific result only for 2 years, so don't leave a long gap between them.
Save your results and get your Readiness Score
Create a free account after the test: your score by topic, a mistakes bank, the complete study notes for the first topic, flashcards and the NDT Level III Formula Sheet.
What's in the premium ASNT NDT Level II PT prep
Premium ASNT NDT Level II PT prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.
Your step-by-step study path
- 1PT Principles and Capillary Action10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Notes free with an account
- 2Penetrant Materials and Classification10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Premium
- 3Selecting the Appropriate PT Process10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Premium
- 4Process Steps, Dwell and Excess Removal10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Premium
- 5Inspection and Evaluation of Indications10 key notes, 130 flashcards, then 500 practice questions in 20 sets of 25Premium
- 6Procedures, Standards and Specific Exam Application10 key notes, 130 flashcards, then 500 practice questions in 20 sets of 25Premium
- Final step: 6 full mock exams50 questions each, timed like test day. Pass them, then book your exam.Premium
Read the complete ASNT NDT Level II PT study notes for “PT Principles and Capillary Action”
Our first full set of comprehensive notes, about 12 minutes of reading: What PT can and cannot do · Capillary action · Properties of a good penetrant · Reverse capillary action and developers · Fluorescent and visible contrast, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.
Study tools included
3,000 practice questions
3,000 exam-style questions per exam, organized topic by topic in sets of 25. Every answer explained, with the rule it comes from.
6 full mock exams
6 full-length timed mock exams per exam, with real question counts and time limits, so test day feels like practice day.
Exam Readiness Score
One 0 to 100 number that tells you when you're ready to book. Reach 80 and you're covered by our Pass Guarantee.
800 flashcards + spaced repetition
800 flashcards per exam, in a deck for each topic, that come back right before you'd forget them. Five minutes a day keeps every number fresh.
60 comprehensive key notes
60 key notes per exam, split across its topics and each explained in full: the concepts, worked exam examples, the traps examiners use and a quick recap. Your first set is free with an account.
Mind maps
See the whole exam on one screen: every topic and the facts under it.
Sample questions with answers
These are the questions in the free test above, with answers. Try the test first. You'll learn more by getting some wrong.
1. Two tight cracks in the same part receive the same penetrant. Crack X is 0.001 in. wide and crack Y is 0.004 in. wide. Treating each as a narrow slot with all else equal, how does the capillary pressure driving penetrant into crack X compare with crack Y?
2. During a materials trial, a liquid shows a contact angle of about 120 degrees on a clean steel test surface. How would this liquid behave as a penetrant?
3. An operator on a hydrophilic post-emulsifiable line skips the water prerinse to save time and applies remover directly over the full penetrant film. What is the most likely result?
4. Penetrant materials are being ordered for an ASME Section V Article 6 examination of Type 316 stainless steel piping. Which contaminants must be controlled and certified for this material?
5. A foundry must process large numbers of aluminum castings with rough as-cast surfaces. Moderate sensitivity is acceptable and a fast, low-cost line is the priority. Which process best fits?
6. A customer needs reliable detection of wide, shallow discontinuities on machined parts. Why is a post-emulsifiable process preferred over a water-washable one for this job?
7. A weld repair on 6061 aluminum was finished with a coarse grinding wheel just before penetrant examination. What should be done before penetrant is applied?
8. Using ASME Section V Table T-672, what is the minimum penetrant dwell time for a carbon steel butt weld examined for cracks with a surface temperature of 45°F, within the standard temperature range?
9. After penetrant dwell on a solvent-removable, visible dye examination of a weld, how should excess penetrant be removed?
10. A cast stainless steel valve body shows a smooth, continuous penetrant line with rounded ends where two metal streams meet in a thin section. What is the most probable discontinuity?
11. An inspector steps from a sunlit yard into a darkened booth and at once begins reading fluorescent indications. The meter shows 1,500 µW/cm² at the surface. What is wrong under ASME Section V Article 6?
12. A steel assembly with a press-fit bushing shows a continuous circular penetrant line exactly around the bushing edge. The joint is a known design feature. How should this be classified?
13. A weld is accepted to ASME Section VIII Division 1 Mandatory Appendix 8. One penetrant indication measures 1/8 in. long and 1/32 in. wide. What is the correct disposition?
14. Developer dried at 9:00 on an ASME Section V Article 6 job. The procedure uses the 10 to 60 minute interpretation window and has no extended time qualified. The inspector returns at 10:20. What should happen?
15. Midway through a job under an ASME Article 6 procedure, the penetrant runs out and the only stock available is a different family group from another manufacturer. What should the Level II do?
Get the full ASNT NDT Level II PT prep
Premium Monthly
- One ASNT Level III exam of your choice: Basic, UT, RT or MT
- 3,000 practice questions + 6 full mock exams per exam
- 800 flashcards + 60 key notes per exam, by topic, plus mind maps
- Spaced repetition + mistakes bank
- Readiness Score & detailed reports
- Video lessons as they release
- Content updates during your access
- 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
- Pass Guarantee: complete the prep, pass or 100% back
Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.
Premium Yearly
- One ASNT Level III exam of your choice: Basic, UT, RT or MT
- 3,000 practice questions + 6 full mock exams per exam
- 800 flashcards + 60 key notes per exam, by topic, plus mind maps
- Spaced repetition + mistakes bank
- Readiness Score & detailed reports
- Video lessons as they release
- Content updates during your access
- 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
- Pass Guarantee: complete the prep, pass or 100% back
Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.
ASNT NDT Level II PT exam FAQ
How many questions are on the ASNT NDT Level II PT exam?
Two multiple-choice exams: General 50 items and Specific 40 items (general industry or pressure equipment sector), with a time limit of general 2 hours; specific 2 hours (4 hours in total). Format: computer-based multiple choice with a scientific calculator provided by asnt. asnt does not publish whether any reference is supplied during these exams; confirm with asnt. this prep covers only the written general and specific exams, not the employer's visual acuity, practical or job-specific exams.
What is the passing score for ASNT NDT Level II PT?
Not published by ASNT for this exam. ASNT says its criterion-referenced cut scores are typically 70% to 80%. Both the General and the Specific exam must be passed, so aim for 80% or higher on each in practice.
How much does the ASNT NDT Level II PT exam cost?
US$740 for ASNT members, US$820 for nonmembers (General plus one Specific exam). Retake of a failed exam or an added sector exam: US$370 / US$410. ASNT fees differ for members and nonmembers and can change, so confirm on the ASNT certification website before you apply.
Which languages is the ASNT NDT Level II PT exam offered in?
US English (ASNT offers an online NDT terminology dictionary in Korean, Mandarin, Spanish, UK English and Arabic).
Where do I take the ASNT NDT Level II PT exam?
Pearson VUE test centers and ASNT Authorized Exam Centers (in person, computer-based, no walk-ins).
Is this ASNT NDT Level II PT practice test free?
Yes. The 15-question practice test on this page is free, with an explanation for every answer and no signup. A free account also unlocks the complete study notes for the first topic. The full ASNT NDT Level II PT prep is Premium at $147 a month for this exam.
What's in the premium ASNT NDT Level II PT prep?
3,000 practice questions organized topic by topic (PT Principles and Capillary Action: 500; Penetrant Materials and Classification: 500; Selecting the Appropriate PT Process: 500; Process Steps, Dwell and Excess Removal: 500; Inspection and Evaluation of Indications: 500; Procedures, Standards and Specific Exam Application: 500), 6 full-length timed mock exams of 50 questions, 800 flashcards and 60 comprehensive key notes split across all 6 topics, plus a mistakes bank and the Readiness Score.
Related practice tests
ASNT NDT Level II, Radiographic Testing (RT)
ASNT's third-party written certification for radiographic technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector.
ASNT NDT Level II, Ultrasonic Testing (UT)
ASNT's third-party written certification for ultrasonic technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector.
ASNT NDT Level II, Visual Testing (VT)
ASNT's third-party Level II certification for visual testing, made up of a 50-item General exam and at least one 40-item Specific exam, each 2 hours.
Exam details are summarized from the official candidate information available in October 2026. ASNT changes formats and fees, so confirm with ASNT Certification Services LLC (American Society for Nondestructive Testing) before you book. NDTLevel3Exam is not affiliated with ASNT or Pearson VUE.