ASNT 9712 Level II, Ultrasonic Testing (UT), written parts: free practice test
ASNT's ISO 9712-based Level II certification for ultrasonic testing, requiring 18 days of training, 180 days of experience and passing all examination elements. The General exam moves to a revised four-domain UT outline for exams after 5 February 2027, and this prep follows that outline while still mapping to the earlier topics. This prep covers only the three written elements, not the practical exams.
Watch the free 4:33 video lesson: the key ASNT 9712 Level II UT concepts →
Premium: 3,000 practice questions, 6 full mock exams, 800 flashcards and 60 comprehensive key notes, topic by topic. See the study path ·
- Lesson 2: Wave modes and velocities in common materialsLongitudinal, shear, surface and plate waves, and how material sets velocity.
- Lesson 3: Acoustic impedance and energy at interfacesReflection and transmission coefficients, couplant choice and why steel-water interfaces lose energy.
- Lesson 4: Refraction, mode conversion and critical anglesSnell's law calculations, wedge design and selecting refracted shear angles.
- Lesson 5: Beam characteristics: near field and spreadNear field length, beam divergence, focusing and their effect on sizing.
- Lesson 6: Transducers, frequency and bandwidthCrystal types, damping, dual elements and choosing frequency for resolution or penetration.
- Lesson 7: Instrument controls and display formatsPulser, receiver, gates, reject and A, B and C scan presentations.
- Lesson 8: Calibration blocks and range standardizationIIW and DSC blocks, exit point, refracted angle and screen range setup.
- Lesson 9: Sensitivity setting, DAC and transfer correctionReference reflectors, distance amplitude curves and correcting for surface differences.
- Lesson 10: Decibel arithmetic for the Level IIAmplitude ratios, gain changes and fast mental decibel calculations.
- Lesson 11: Immersion and permanently installed systemsWater path, focusing, immersion calibration and monitoring sensors in service.
- Lesson 12: Scan plans for plate, bar and forgingsMatching beam direction to rolling and forging flaw orientation.
- Lesson 13: Weld examination with angle beamsSkip distance, surface distance, depth calculations and full volume coverage.
- Lesson 14: Castings and coarse-grained austenitic materialsScatter, beam skew, lower frequencies and longitudinal angle beam techniques.
- Lesson 15: Thickness measurement and corrosion mappingGauge modes, coatings, temperature effects and in-service wall loss.
- Lesson 16: Bonded structures and composite inspectionDisbonds and voids by pulse echo, through transmission and resonance.
- Lesson 17: Relevant, non-relevant and geometric indicationsPlotting echoes to separate root, counterbore and mode-converted signals from flaws.
- Lesson 18: Characterizing planar and volumetric discontinuitiesEcho dynamics, orbiting and rotation to classify cracks, fusion defects and porosity.
- Lesson 19: Sizing methods and their limitsSix and twenty decibel drop, amplitude methods and when each misleads.
- Lesson 20: Reporting and documenting UT resultsWhat a report must record: procedure, equipment, calibration, coverage and disposition.
- Lesson 21: Certification, retakes, renewal and UT safetyASNT 9712 training, experience, retake waiting periods, five-year renewal and site safety.
- Lesson 22: Specific exam: ASME Section V Article 4Calibration checks, scan overlap, scanning speed and recording levels for welds.
- Lesson 23: Instruction preparation: writing a UT instructionStructure, weighting and complete settings a Level I can follow without questions.
Keep going after the free lesson. Every topic gets its own lesson, plus the full question bank, timed simulations and study tools.
About the ASNT 9712 Level II UT exam
ASNT's ISO 9712-based Level II certification for ultrasonic testing, requiring 18 days of training, 180 days of experience and passing all examination elements. The General exam moves to a revised four-domain UT outline for exams after 5 February 2027, and this prep follows that outline while still mapping to the earlier topics. This prep covers only the three written elements, not the practical exams.
What's on the exam
Each branch is a topic in the official outline. Members see every key fact on the full mind map. Read the free study guide →
How to pass the ASNT 9712 Level II UT exam
- Check your exam date against 5 February 2027. Earlier General exams use the six-topic outline, including bonded structures; later ones use four job-task domains.
- Each written element has its own 70% minimum, so a strong General score can't offset a weak Instruction Preparation result.
- Instruction Preparation is 20 items in 1 hour, and the detailed test instructions carry 40% of its weighting. Practice writing frequency, angle, reference level and scan coverage as stated values.
- Move quickly on the arithmetic: Snell's law, dB ratios, and time-base positions. ASNT supplies the calculator, so review its guide before test day.
Save your results and get your Readiness Score
Create a free account after the test: your score by topic, a mistakes bank, the complete study notes for the first topic, flashcards and the NDT Level III Formula Sheet.
What's in the premium ASNT 9712 Level II UT prep
Premium ASNT 9712 Level II UT prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.
Your step-by-step study path
- 1UT Principles and Techniques10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Notes free with an account
- 2Examination of Materials and Product Forms10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Premium
- 3UT Data Collection, Interpretation and Reporting10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Premium
- 4UT Training, Certification and Safety10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25Premium
- 5Specific Exam: Pre- and In-Service Applications10 key notes, 130 flashcards, then 500 practice questions in 20 sets of 25Premium
- 6Instruction Preparation10 key notes, 130 flashcards, then 500 practice questions in 20 sets of 25Premium
- Final step: 6 full mock exams110 questions each, timed like test day. Pass them, then book your exam.Premium
Read the complete ASNT 9712 Level II UT study notes for “UT Principles and Techniques”
Our first full set of comprehensive notes, about 14 minutes of reading: Wave modes and velocity · Refraction and critical angles · The sound beam · Instruments and standardization · Choosing a technique, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.
Study tools included
3,000 practice questions
3,000 exam-style questions per exam, organized topic by topic in sets of 25. Every answer explained, with the rule it comes from.
6 full mock exams
6 full-length timed mock exams per exam, with real question counts and time limits, so test day feels like practice day.
Exam Readiness Score
One 0 to 100 number that tells you when you're ready to book. Reach 80 and you're covered by our Pass Guarantee.
800 flashcards + spaced repetition
800 flashcards per exam, in a deck for each topic, that come back right before you'd forget them. Five minutes a day keeps every number fresh.
60 comprehensive key notes
60 key notes per exam, split across its topics and each explained in full: the concepts, worked exam examples, the traps examiners use and a quick recap. Your first set is free with an account.
Mind maps
See the whole exam on one screen: every topic and the facts under it.
Sample questions with answers
These are the questions in the free test above, with answers. Try the test first. You'll learn more by getting some wrong.
1. A longitudinal-wave search unit is standardized on a 1 in thick steel block so that 10 screen divisions equal 5 in of steel. At which division should the third back-wall echo appear?
2. An acrylic wedge (2,730 m/s) puts a 20° incident beam into steel (longitudinal 5,920 m/s, shear 3,230 m/s). What is in the steel?
3. A reference reflector peaks at 80% FSH with 40 dB on the calibration block. On the production part, the same reflector needs 46 dB for 80% FSH because of coupling and surface loss. What should be done?
4. Which search unit produces the narrowest beam in the same steel?
5. A hot pipe at about 400 °F reads 0.520 in on a gauge calibrated on a room-temperature block. Which statement is correct?
6. A painted vessel needs wall readings and the paint can't be removed. Which technique best excludes the coating thickness from the reading?
7. A narrow-gap weld is suspected of a vertical planar lack of fusion at mid-wall. A single angle-beam search unit gets little echo. Which technique best suits this reflector?
8. A stainless steel weld in an austenitic pipe gives heavy noise and no usable shear-wave response at a suspected inside-surface crack. Which change is most likely to give a usable response?
9. During angle-beam evaluation, an echo falls off sharply as the search unit is rotated a few degrees and moved in a small orbit around the peak. How is this best characterized?
10. An angle-beam search unit shows an echo at a fixed position on the screen that stays there when the unit is moved along the plate or lifted clear of it. What is the most likely source?
11. A small reflector, narrower than the beam, is sized by the 6 dB drop method. How does the measured length compare with the true length?
12. A candidate fails the ASNT 9712 Level II UT General exam element for the first time. What does ASNT's retake policy allow?
13. An ASME Section V Article 4 examination ends with a calibration check. A DAC point has dropped by 3 dB from its original setting. What is required?
14. Under ASME Section VIII Division 1 Mandatory Appendix 12, a 1 in thick weld shows a non-planar indication above the reference level, 0.30 in long, not characterized as a crack or lack of fusion. What is the disposition?
15. In a written UT instruction, which section should state the search unit frequency, refracted angle and reference gain setting?
Get the full ASNT 9712 Level II UT prep
Premium Monthly
- One ASNT Level III exam of your choice: Basic, UT, RT or MT
- 3,000 practice questions + 6 full mock exams per exam
- 800 flashcards + 60 key notes per exam, by topic, plus mind maps
- Spaced repetition + mistakes bank
- Readiness Score & detailed reports
- Video lessons as they release
- Content updates during your access
- 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
- Pass Guarantee: complete the prep, pass or 100% back
Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.
Premium Yearly
- One ASNT Level III exam of your choice: Basic, UT, RT or MT
- 3,000 practice questions + 6 full mock exams per exam
- 800 flashcards + 60 key notes per exam, by topic, plus mind maps
- Spaced repetition + mistakes bank
- Readiness Score & detailed reports
- Video lessons as they release
- Content updates during your access
- 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
- Pass Guarantee: complete the prep, pass or 100% back
Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.
ASNT 9712 Level II UT exam FAQ
How many questions are on the ASNT 9712 Level II UT exam?
110 written items over three computer-based elements: General 50, Specific 40 (Pre- and In-Service) and Instruction Preparation 20. A practical exam is also required: castings/forgings (2 parts) or welds (2 areas of interest), straight and angle beam, with a time limit of 5 hours of written exams: general 2 hours, specific 2 hours, instruction preparation 1 hour. each practical (castings/forgings or welds) is a further 2 hours. Format: computer-based with an on-screen scientific calculator supplied by asnt. codes, standards, procedures and other aids may be used only if asnt supplies or authorizes them for that exam, and asnt's candidate pages do not list them, so confirm with asnt. instruction preparation uses multiple-choice and multiple-response items. this prep covers only the written parts, with 4-option practice items; it does not cover the hands-on practical exams.
What is the passing score for ASNT 9712 Level II UT?
At least 70% on each written element (General, Specific and Instruction Preparation) and at least 80% on each practical specimen.
How much does the ASNT 9712 Level II UT exam cost?
US$1,270 for ASNT members, US$1,345 for nonmembers (single technique); all techniques US$1,620 / US$1,715. Retakes: General or Specific US$415 / US$465, Instruction Preparation US$400 / US$455, castings/forgings or welds practical US$500 / US$590. ASNT fees differ for members and nonmembers and can change, so confirm on the ASNT certification website before you apply.
Which languages is the ASNT 9712 Level II UT exam offered in?
English only (an online NDT terminology dictionary covers Korean, Mandarin, Spanish, UK English and Arabic).
Where do I take the ASNT 9712 Level II UT exam?
Written exams at Pearson VUE test centers or ASNT Authorized Exam Centers (computer-based); practical exams only at Authorized Exam Centers.
Is this ASNT 9712 Level II UT practice test free?
Yes. The 15-question practice test on this page is free, with an explanation for every answer and no signup. A free account also unlocks the complete study notes for the first topic. The full ASNT 9712 Level II UT prep is Premium at $147 a month for this exam.
What's in the premium ASNT 9712 Level II UT prep?
3,000 practice questions organized topic by topic (UT Principles and Techniques: 500; Examination of Materials and Product Forms: 500; UT Data Collection, Interpretation and Reporting: 500; UT Training, Certification and Safety: 500; Specific Exam: Pre- and In-Service Applications: 500; Instruction Preparation: 500), 6 full-length timed mock exams of 110 questions, 800 flashcards and 60 comprehensive key notes split across all 6 topics, plus a mistakes bank and the Readiness Score.
Related practice tests
ASNT NDT Level II, Liquid Penetrant Testing (PT)
ASNT's third-party written certification for liquid penetrant technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector.
ASNT NDT Level II, Radiographic Testing (RT)
ASNT's third-party written certification for radiographic technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector.
ASNT NDT Level II, Ultrasonic Testing (UT)
ASNT's third-party written certification for ultrasonic technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector.
Exam details are summarized from the official candidate information available in October 2026. ASNT changes formats and fees, so confirm with ASNT Certification Services LLC (American Society for Nondestructive Testing) before you book. NDTLevel3Exam is not affiliated with ASNT or Pearson VUE.