Try the full study dashboard free, no signup: practice, flashcards and your Exam Readiness Score. Open it →
Home / Practice tests / MT Level III
ASNT NDT Level III · Last updated November 2026

ASNT NDT Level III Magnetic Particle Testing (MT) Exam: free practice test

The ASNT Level III magnetic particle exam: 90 questions in 2 hours across five domains: MT principles and theory, equipment and materials, interpreting, evaluating and documenting results, codes, standards, procedures and techniques, and MT training and certification programs.

Watch the free 4:22 video lesson: the key MT Level III concepts →

Premium: 3,000 practice questions, 6 full mock exams, 800 flashcards and 60 comprehensive key notes, topic by topic. See the study path ·

Or open the free MT Level III study dashboard: flashcards, notes and your Readiness Score, no signup →

About the MT Level III exam

The ASNT Level III magnetic particle exam: 90 questions in 2 hours across five domains: MT principles and theory, equipment and materials, interpreting, evaluating and documenting results, codes, standards, procedures and techniques, and MT training and certification programs.

What's on the exam

MT Level III
Magnetism Principles and Theory
7 key facts
Magnetization Techniques and Current Types
7 key facts
Equipment, Media and Lighting
6 key facts
Field Verification and Demagnetization
6 key facts
Interpretation and Evaluation
6 key facts
Codes, Procedures and MT Program Management
5 key facts

Each branch is a topic in the official outline. Members see every key fact on the full mind map. Read the free study guide →

How to pass the MT Level III exam

  • 90 questions in 2 hours is 80 seconds each. Current calculations (coil, direct contact, prods) should take under a minute.
  • Learn the rules of thumb with their source: 300 to 800 A per inch of diameter for direct contact, NI = 45,000 ÷ (L/D) for a low fill-factor coil, 90 to 125 A per inch of prod spacing.
  • A discontinuity shows best when it lies across the field. For every technique, ask which direction the field runs and which flaws it will miss.
  • Know the media checks: settling test volumes, UV-A intensity and ambient light limits, and the 10 lb / 40 lb yoke lift tests.

Save your results and get your Readiness Score

Create a free account after the test: your score by topic, a mistakes bank, the complete study notes for the first topic, flashcards and the NDT Level III Formula Sheet.

Take the test first

What's in the premium MT Level III prep

Premium MT Level III prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.

3,000practice questions, every answer explained
6full-length mock exams, 90 questions each, timed
800flashcards with spaced repetition, sorted by topic
60comprehensive key notes across 6 topics

Your step-by-step study path

  1. 1
    Magnetism Principles and Theory10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25
    Notes free with an account
  2. 2
    Magnetization Techniques and Current Types10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25
    Premium
  3. 3
    Equipment, Media and Lighting10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25
    Premium
  4. 4
    Field Verification and Demagnetization10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25
    Premium
  5. 5
    Interpretation and Evaluation10 key notes, 130 flashcards, then 500 practice questions in 20 sets of 25
    Premium
  6. 6
    Codes, Procedures and MT Program Management10 key notes, 130 flashcards, then 500 practice questions in 20 sets of 25
    Premium
  7. Final step: 6 full mock exams90 questions each, timed like test day. Pass them, then book your exam.
    Premium
Free with an account

Read the complete MT Level III study notes for “Magnetism Principles and Theory”

Our first full set of comprehensive notes, about 15 minutes of reading: How a leakage field forms · Materials and permeability · The hysteresis loop · Fields from current · Temperature and the Curie point, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.

Open the free dashboard

Study tools included

3,000 practice questions

3,000 exam-style questions per exam, organized topic by topic in sets of 25. Every answer explained, with the rule it comes from.

6 full mock exams

6 full-length timed mock exams per exam, with real question counts and time limits, so test day feels like practice day.

Exam Readiness Score

One 0 to 100 number that tells you when you're ready to book. Reach 80 and you're covered by our Pass Guarantee.

800 flashcards + spaced repetition

800 flashcards per exam, in a deck for each topic, that come back right before you'd forget them. Five minutes a day keeps every number fresh.

60 comprehensive key notes

60 key notes per exam, split across its topics and each explained in full: the concepts, worked exam examples, the traps examiners use and a quick recap. Your first set is free with an account.

Mind maps

See the whole exam on one screen: every topic and the facts under it.

Sample questions with answers

These are the questions in the free test above, with answers. Try the test first. You'll learn more by getting some wrong.

1. A steel bar is magnetized by passing current through it from end to end (a head shot). Which discontinuities are best detected?
Answer: Longitudinal discontinuities parallel to the bar axis. Current along the bar creates a circular field around its axis. Flaws show best when they lie across the field, so a head shot finds longitudinal flaws. Transverse flaws need a longitudinal field, for example from a coil.
2. The reverse magnetizing force needed to bring the residual magnetism of a material to zero is called:
Answer: Coercive force. On the hysteresis loop, coercive force is the reverse field needed to reduce flux density to zero. Retentivity is the residual flux left when the magnetizing force is removed; materials with high coercive force are harder to demagnetize.
3. Above which temperature does iron lose its ferromagnetic properties?
Answer: Its Curie temperature, about 770 °C (1,418 °F). Above the Curie temperature, about 770 °C (1,418 °F) for iron, a ferromagnetic material becomes paramagnetic. Heating above it is a complete but rarely practical way to demagnetize.
4. Under ASME Section V Article 7, what magnetizing current range applies to a direct contact (head shot) examination of a 4 in diameter round bar?
Answer: 1,200 to 3,200 A. ASME Section V specifies 300 to 800 A per inch of outer diameter for direct contact magnetization: 4 × 300 = 1,200 A to 4 × 800 = 3,200 A.
5. A 15 in long, 2.5 in diameter part lies against the inside wall of a 5-turn, low fill-factor coil. Using NI = 45,000 ÷ (L/D), what current is needed?
Answer: 1,500 A. L/D = 15 ÷ 2.5 = 6. NI = 45,000 ÷ 6 = 7,500 ampere-turns. I = 7,500 ÷ 5 turns = 1,500 A. (The formula applies for L/D of 2 or more; use 15 for L/D above 15.)
6. Under ASME Section V Article 7, what current range applies to prods spaced 6 in apart on a 1 in thick plate?
Answer: 600 to 750 A. For sections 3/4 in (19 mm) or thicker, ASME Section V specifies 100 to 125 A per inch of prod spacing: 6 × 100 = 600 A to 6 × 125 = 750 A. (540 to 660 A would be the 90 to 110 A/in range for thinner sections.)
7. Which magnetizing current gives the best sensitivity to subsurface discontinuities when used with dry powder?
Answer: Half-wave rectified current. AC concentrates the field near the surface (skin effect). Rectified current penetrates deeper, and the pulsing of half-wave rectified current also helps dry particles move to leakage fields.
8. In a settling test, what particle volume per 100 mL of bath is the normal range for a wet fluorescent magnetic particle suspension?
Answer: 0.1 to 0.4 mL. ASTM E709 and E1444 give 0.1 to 0.4 mL per 100 mL for fluorescent baths and 1.2 to 2.4 mL for visible (color contrast) baths, read after the specified settling time.
9. Under ASME Section V Article 7, what is the minimum UV-A (black light) intensity at the examination surface for fluorescent particles?
Answer: 1000 µW/cm². ASME Section V requires at least 1000 µW/cm² of UV-A at the examination surface, in a darkened area. Check the intensity before use and at the intervals the code sets.
10. Under ASME Section V Article 7, what minimum lifting power must an AC yoke have at its maximum pole spacing?
Answer: 10 lb (4.5 kg). ASME Section V requires an AC yoke to lift at least 10 lb (4.5 kg) at the maximum pole spacing to be used. DC and permanent-magnet yokes must lift at least 40 lb (18 kg).
11. Which statement best describes a pie-shaped magnetic particle field indicator?
Answer: It shows field direction and gives a qualitative check of field adequacy at the surface. The pie gage shows where particles collect (field direction) and whether a usable field is present. It doesn't measure field strength; a Hall-effect gaussmeter does.
12. A part was magnetized with DC. Which demagnetization method is most effective at removing the deep residual field?
Answer: Reversing DC with step-down current. AC demagnetization only reaches near the surface because of the skin effect. Reversing DC that steps down in amplitude penetrates as deep as the original DC field and removes it.
13. A broad, fuzzy indication lines up with an abrupt change in section thickness and gets weaker when the part is re-examined at lower current. What is it most likely to be?
Answer: A nonrelevant indication from flux leakage at the change in section. Abrupt changes in section force flux out of the part and attract particles without any discontinuity. Such nonrelevant indications are broad, follow the geometry and fade at lower field strength.
14. Compared with a surface crack, an indication from a subsurface discontinuity is typically:
Answer: Broader, more diffuse and less clearly defined. The leakage field from a subsurface flaw spreads out before it reaches the surface, so particles form a broad, fuzzy indication. Surface cracks give sharp, tight lines.
15. Under ASME Section V Article 7, what is the maximum prod spacing?
Answer: 8 in (200 mm). ASME Section V limits prod spacing to 8 in (200 mm). Shorter spacing may be used for geometry, but below about 3 in (75 mm) the particles band around the prods and prod technique is usually not practical.

Get the full MT Level III prep

Most popular · cancel anytime

Premium Monthly

$147/month
per exam
About $4.83 a day · less than a retake fee, for the certification that lets you approve procedures and certify technicians
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.

Best value · 3 months free

Premium Yearly

$1,323/year
per exam
Pay for 9 months, get 12. Save $441 against paying monthly.
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.

Pass Guarantee. Complete the full prep, sit your exam within 60 days, and if you don't pass we refund 100% of your subscription payments. See the requirements
Secure checkout by Stripe Card, Apple Pay, Google Pay Pass Guarantee

Certification guide

How to become an ASNT NDT Level III: ASNT NDT Level III is the credential for NDT professionals who write procedures, interpret codes, choose methods and train and certify technicians. It is issued by [ASNT Certification Services](https://certification.asnt.org/certification/asnt-ndt-level-iii) after you prove your education and Level II experience and pass the Basic exam plus at least one method exam. Here is the path, what it costs and how long it takes.

MT Level III exam FAQ

How many questions are on the MT Level III exam?

90 multiple-choice questions (some are unscored pretest items), with a time limit of 2 hours. Format: closed book, computer-based, with an on-screen calculator.

What is the passing score for MT Level III?

Not published per exam. Aim for 80% or higher in practice (ASNT says its criterion-referenced cut scores are typically 70% to 80%).

How much does the MT Level III exam cost?

US$525 for ASNT members, US$605 for nonmembers (retake US$455 / US$535). ASNT fees differ for members and nonmembers and can change, so confirm on the ASNT certification website before you apply.

Which languages is the MT Level III exam offered in?

English (an online NDT terminology translation dictionary is available).

Where do I take the MT Level III exam?

Pearson VUE test centers and ASNT Authorized Exam Centers (in person, computer-based).

Is this MT Level III practice test free?

Yes. The 15-question practice test on this page is free, with an explanation for every answer and no signup. A free account also unlocks the complete study notes for the first topic. The full MT Level III prep is Premium at $147 a month for this exam.

What's in the premium MT Level III prep?

3,000 practice questions organized topic by topic (Magnetism Principles and Theory: 500; Magnetization Techniques and Current Types: 500; Equipment, Media and Lighting: 500; Field Verification and Demagnetization: 500; Interpretation and Evaluation: 500; Codes, Procedures and MT Program Management: 500), 6 full-length timed mock exams of 90 questions, 800 flashcards and 60 comprehensive key notes split across all 6 topics, plus a mistakes bank and the Readiness Score.

Compare MT Level III with the other ASNT Level III exams

Related practice tests

Exam details are summarized from the official candidate information available in October 2026. ASNT changes formats and fees, so confirm with ASNT Certification Services LLC (American Society for Nondestructive Testing) before you book. NDTLevel3Exam is not affiliated with ASNT or Pearson VUE.

Start the free test