Try the full study dashboard free, no signup: practice, flashcards and your Exam Readiness Score. Open it →
Home / Study guides / MT Level III
Study guide · Last updated November 2026

MT Level III Exam Study Guide (2026)

Everything the ASNT NDT Level III Magnetic Particle Testing (MT) Exam tests, topic by topic: what each section covers, the facts that come up most, and how to study it. Pair it with the free 15-question practice test.

The exam at a glance

Questions90 multiple-choice questions (some are unscored pretest items)
Time2 hours
Passing scoreNot published per exam. Aim for 80% or higher in practice (ASNT says its criterion-referenced cut scores are typically 70% to 80%)
FormatClosed book, computer-based, with an on-screen calculator
Certifying bodyASNT Certification Services LLC (American Society for Nondestructive Testing)
Test providerPearson VUE test centers and ASNT Authorized Exam Centers (in person, computer-based)

Mind map: the whole exam on one screen

MT Level III
Magnetism Principles and Theory
Coercive forceRetentivityHead shot field directionCoil shot field direction
Magnetization Techniques and Current Types
Direct contact current (ASME V)Coil formula, part at side of a low fill-factor coilProd current at 3/4 in or thicker (ASME V)Best current for subsurface flaws
Equipment, Media and Lighting
AC yoke lift test (ASME V)DC yoke lift test (ASME V)Fluorescent bath concentrationVisible bath concentration
Field Verification and Demagnetization
6 key facts
Interpretation and Evaluation
6 key facts
Codes, Procedures and MT Program Management
5 key facts
Free with an account

Read the complete MT Level III study notes for “Magnetism Principles and Theory”

Our first full set of comprehensive notes, about 15 minutes of reading: How a leakage field forms · Materials and permeability · The hysteresis loop · Fields from current · Temperature and the Curie point, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.

Open the free dashboard

1. Magnetism Principles and Theory

Magnetic fields, flux leakage, permeability and the hysteresis loop. The theory behind every technique choice on the MT exam.

Key facts

  • MT works because a discontinuity across the field forces flux out of the part (a leakage field), which attracts particles.
  • Ferromagnetic materials (iron, nickel, cobalt and most of their alloys) are strongly attracted; austenitic stainless steel, aluminum and copper are not.
  • Permeability (μ = B ÷ H) is how easily a material is magnetized. Low-carbon steels have high permeability; hardened steels have lower permeability and higher retentivity.
  • Hysteresis loop terms: saturation, residual magnetism (retentivity), coercive force (reverse field to bring B to zero).
  • Current through a conductor makes a circular field (right-hand rule); current through a coil makes a longitudinal field inside it.
  • Flaws show best perpendicular to the field and are hard to see within about 45° of parallel. Test each area in two directions about 90° apart.
  • Above the Curie temperature (about 770 °C for iron) a material loses its ferromagnetism.

Flashcards

Coercive forceReverse magnetizing force needed to bring flux density to zero.
RetentivityAbility to keep residual magnetism after the magnetizing force is removed.
Head shot field directionCircular, around the part axis: finds longitudinal flaws.
Coil shot field directionLongitudinal, along the part axis: finds transverse flaws.

Exam tip: For every technique question, sketch the field direction first. The right answer is the flaw orientation at 90° to it.

2. Magnetization Techniques and Current Types

Direct and indirect magnetization (head shot, central conductor, coil, prods, yokes), current types, and the current rules of thumb codes use.

Key facts

  • Direct magnetization passes current through the part (head shot, prods); indirect magnetization induces a field (coil, central conductor, yoke).
  • ASME Section V direct contact: 300 to 800 A per inch of outer diameter.
  • Low fill-factor coil with the part against the coil wall: NI = 45,000 ÷ (L/D), for L/D of 2 or more (use 15 when L/D exceeds 15).
  • ASME Section V prods: 90 to 110 A per inch of spacing below 3/4 in thickness, 100 to 125 A per inch at 3/4 in and over; spacing 3 to 8 in.
  • AC concentrates the field at the surface (skin effect) and gives particles mobility: best for surface cracks. Rectified current (HWDC, FWDC) penetrates deeper: better for subsurface.
  • Central conductors magnetize the inside and outside of hollow parts and avoid arc burns; offset conductors cover large diameters in overlapping positions.
  • Continuous method: particles applied while current flows (most sensitive). Residual method: particles applied after, only for high-retentivity steels.

Flashcards

Direct contact current (ASME V)300 to 800 A per inch of diameter.
Coil formula, part at side of a low fill-factor coilNI = 45,000 ÷ (L/D).
Prod current at 3/4 in or thicker (ASME V)100 to 125 A per inch of prod spacing.
Best current for subsurface flawsRectified current, especially half-wave DC with dry powder.

Exam tip: Write the formula, then plug in. Coil questions often hide the number of turns, which you must divide by at the end.

3. Equipment, Media and Lighting

Yokes, benches and power packs, dry and wet particles, bath checks, and the lighting rules for visible and fluorescent examination.

Key facts

  • Yokes give a longitudinal field between the poles. ASME Section V lift test: AC yoke at least 10 lb (4.5 kg), DC or permanent magnet at least 40 lb (18 kg) at maximum pole spacing.
  • Dry particles suit rough surfaces and hot parts and give good subsurface sensitivity with HWDC; wet particles (especially fluorescent) give the best sensitivity to fine surface cracks.
  • Settling test (ASTM E709 / E1444): fluorescent 0.1 to 0.4 mL per 100 mL, visible 1.2 to 2.4 mL per 100 mL.
  • Fluorescent examination (ASME Section V): UV-A at least 1000 µW/cm² at the surface, in a darkened area; allow eyes to adapt to the dark before inspecting.
  • Visible particles need white light on the surface; ASME Section V requires at least 100 fc (1000 lx).
  • Bath contamination, wrong concentration and weak UV-A are the most common causes of missed indications.

Flashcards

AC yoke lift test (ASME V)At least 10 lb (4.5 kg) at maximum pole spacing.
DC yoke lift test (ASME V)At least 40 lb (18 kg) at maximum pole spacing.
Fluorescent bath concentration0.1 to 0.4 mL per 100 mL.
Visible bath concentration1.2 to 2.4 mL per 100 mL.

Exam tip: Pair every media number with its condition: fluorescent or visible, AC or DC. Distractors swap the pairs.

Test yourself on these topics

Take the free 15-question MT Level III test, then save your results to unlock your Readiness Score and the mistakes bank.

Start the free test

4. Field Verification and Demagnetization

Checking field direction and adequacy, measuring field strength, and removing residual magnetism.

Key facts

  • Field indicators: pie gages and shims (artificial flaw standards) show direction and adequacy; Hall-effect gaussmeters measure tangential field strength.
  • A pie gage is qualitative; it doesn't measure field strength.
4 more key facts, 10 key notes, 135 flashcards and 500 practice questions for this topic are in premium.

Flashcards

Pie gage showsField direction and qualitative adequacy, not strength.

Exam tip: If the question mentions DC and deep fields, the demag answer is reversing DC. AC can't reach that deep.

5. Interpretation and Evaluation

Telling relevant from nonrelevant and false indications, recognizing discontinuity types, and documenting results.

Key facts

  • False indications come from poor cleaning or drainage, not leakage fields; they wipe off and don't reform.
  • Nonrelevant indications are real leakage fields without a discontinuity: changes in section, sharp corners, dissimilar metal or permeability boundaries, magnetic writing, heat-affected zone edges.
4 more key facts, 10 key notes, 130 flashcards and 500 practice questions for this topic are in premium.

Flashcards

Nonrelevant indicationA real leakage field with no discontinuity, such as at a section change.

Exam tip: If an indication follows geometry and fades at lower current, call it nonrelevant. If it stays and is sharp, treat it as relevant.

6. Codes, Procedures and MT Program Management

ASME Section V Article 7, ASTM E709 and E1444, writing technique sheets and procedures, and running MT training, exams and audits.

Key facts

  • ASME Section V Article 7 sets technique rules (currents, prod spacing, yoke lift tests, lighting, field verification); acceptance criteria come from the referencing code.
  • Prod spacing: 8 in (200 mm) maximum; below about 3 in (75 mm) is usually not practical because particles band around the prods.
3 more key facts, 10 key notes, 130 flashcards and 500 practice questions for this topic are in premium.

Flashcards

Maximum prod spacing (ASME V)8 in (200 mm).

Exam tip: On exam day, attach every number to its document. 'Per ASME Section V' and 'per ASTM E1444' can have different answers.

How to pass

  • 90 questions in 2 hours is 80 seconds each. Current calculations (coil, direct contact, prods) should take under a minute.
  • Learn the rules of thumb with their source: 300 to 800 A per inch of diameter for direct contact, NI = 45,000 ÷ (L/D) for a low fill-factor coil, 90 to 125 A per inch of prod spacing.
  • A discontinuity shows best when it lies across the field. For every technique, ask which direction the field runs and which flaws it will miss.
  • Know the media checks: settling test volumes, UV-A intensity and ambient light limits, and the 10 lb / 40 lb yoke lift tests.

Frequently asked questions

How long should I study for the MT Level III exam?

Most working candidates need 4 to 8 weeks at 45 to 60 minutes a day. Book your exam once your Readiness Score has stayed at 80 or higher for about a week.

Can I take the MT Level III exam online?

No. ASNT NDT Level III exams are taken in person, on a computer, at Pearson VUE test centers or ASNT Authorized Exam Centers. Format: closed book, computer-based, with an on-screen calculator. Check ASNT's current exam information for the rules.

What score do I need to pass the MT Level III exam?

Not published per exam. Aim for 80% or higher in practice (ASNT says its criterion-referenced cut scores are typically 70% to 80%). The exam has 90 multiple-choice questions (some are unscored pretest items) and a time limit of 2 hours.

What are the most tested topics?

The outline covers magnetism principles and theory, magnetization techniques and current types, equipment, media and lighting, field verification and demagnetization, interpretation and evaluation, codes, procedures and mt program management. Use the free practice test to see which ones you need most.

The premium MT Level III study path

Premium MT Level III prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.

3,000practice questions, every answer explained
6full-length mock exams, 90 questions each, timed
800flashcards with spaced repetition, sorted by topic
60comprehensive key notes across 6 topics

Your step-by-step study path

  1. 1
    Magnetism Principles and Theory10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25
    Notes free with an account
  2. 2
    Magnetization Techniques and Current Types10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25
    Premium
  3. 3
    Equipment, Media and Lighting10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25
    Premium
  4. 4
    Field Verification and Demagnetization10 key notes, 135 flashcards, then 500 practice questions in 20 sets of 25
    Premium
  5. 5
    Interpretation and Evaluation10 key notes, 130 flashcards, then 500 practice questions in 20 sets of 25
    Premium
  6. 6
    Codes, Procedures and MT Program Management10 key notes, 130 flashcards, then 500 practice questions in 20 sets of 25
    Premium
  7. Final step: 6 full mock exams90 questions each, timed like test day. Pass them, then book your exam.
    Premium

Get every note, flashcard and question

Most popular · cancel anytime

Premium Monthly

$147/month
per exam
About $4.83 a day · less than a retake fee, for the certification that lets you approve procedures and certify technicians
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.

Best value · 3 months free

Premium Yearly

$1,323/year
per exam
Pay for 9 months, get 12. Save $441 against paying monthly.
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.

Pass Guarantee. Complete the full prep, sit your exam within 60 days, and if you don't pass we refund 100% of your subscription payments. See the requirements
Secure checkout by Stripe Card, Apple Pay, Google Pay Pass Guarantee

Summarized from ASNT's official candidate information and the rules cited, checked October 2026. Confirm current requirements with ASNT Certification Services LLC (American Society for Nondestructive Testing).

Start the free test