Try the full study dashboard free, no signup: practice, flashcards and your Exam Readiness Score. Open it →
Home / Practice tests / CSWIP NDT Level 3
CSWIP (TWI) · Last updated November 2026

CSWIP NDT Level 3 (CSWIP-ISO-NDT-11/93-R): free practice test

CSWIP's ISO 9712 Level 3 route consists of a Basic examination, valid across further Level 3 methods, and a Main Method examination in the chosen method and sector. All six sections need at least 70%, and the governing document and its appendices were reissued in July 2026. This prep covers only the written knowledge sections; candidates without Level 2 must also pass the relevant practical examination.

Watch the free 4:34 video lesson: the key CSWIP NDT Level 3 concepts →

Premium: 3,000 practice questions, 6 full mock exams, 800 flashcards and 60 comprehensive key notes, topic by topic. See the study path ·

Or open the free CSWIP NDT Level 3 study dashboard: flashcards, notes and your Readiness Score, no signup →

About the CSWIP NDT Level 3 exam

CSWIP's ISO 9712 Level 3 route consists of a Basic examination, valid across further Level 3 methods, and a Main Method examination in the chosen method and sector. All six sections need at least 70%, and the governing document and its appendices were reissued in July 2026. This prep covers only the written knowledge sections; candidates without Level 2 must also pass the relevant practical examination.

What's on the exam

CSWIP NDT Level 3
Section A: Materials and Process Technology
7 key facts
Section A: Discontinuities and Failure Modes
6 key facts
Section B: CSWIP Scheme, ISO 9712 and SNT-TC-1A
7 key facts
Section C: MT, PT and VT at Level 2
6 key facts
Section C: UT, RT, ET, AE and TIR at Level 2
6 key facts
Section D: Level 3 Main Method Knowledge
7 key facts
Section E: Application, Codes and Standards
6 key facts
Section F: Procedure Writing
6 key facts

Each branch is a topic in the official outline. Members see every key fact on the full mind map. Read the free study guide →

How to pass the CSWIP NDT Level 3 exam

  • Download the Appendix 1 part for your method, because it sets the sector options and the syllabus. For UT, the sectors are Welds, Castings and Wrought Products (including forgings).
  • Section C is 60 of the 145 multiple-choice questions. You choose at least four methods, 15 questions each, and one must be UT or RT, so pick the four you can answer at Level 2 depth.
  • Sections A and C both allow 2 minutes per question, and each needs 70% on its own, so a strong Section C cannot rescue a weak Section A. Once you pass Sections A, B and C, you do not resit them for later Level 3 methods.
  • After a failure you may take two retests of the failed sections within one year of the initial test, and not within 30 days unless you complete further specific training. Book retests with that window in mind.

Save your results and get your Readiness Score

Create a free account after the test: your score by topic, a mistakes bank, the complete study notes for the first topic, flashcards and the NDT Level III Formula Sheet.

Take the test first

What's in the premium CSWIP NDT Level 3 prep

Premium CSWIP NDT Level 3 prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.

3,000practice questions, every answer explained
6full-length mock exams, 50 questions each, timed
800flashcards with spaced repetition, sorted by topic
60comprehensive key notes across 8 topics

Your step-by-step study path

  1. 1
    Section A: Materials and Process Technology8 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Notes free with an account
  2. 2
    Section A: Discontinuities and Failure Modes8 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  3. 3
    Section B: CSWIP Scheme, ISO 9712 and SNT-TC-1A8 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  4. 4
    Section C: MT, PT and VT at Level 28 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  5. 5
    Section C: UT, RT, ET, AE and TIR at Level 27 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  6. 6
    Section D: Level 3 Main Method Knowledge7 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  7. 7
    Section E: Application, Codes and Standards7 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  8. 8
    Section F: Procedure Writing7 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  9. Final step: 6 full mock exams50 questions each, timed like test day. Pass them, then book your exam.
    Premium
Free with an account

Read the complete CSWIP NDT Level 3 study notes for “Section A: Materials and Process Technology”

Our first full set of comprehensive notes, about 15 minutes of reading: From liquid steel to semi-finished product · Casting routes · Wrought routes · Heat treatment · Machining, finishing and quality statistics, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.

Open the free dashboard

Study tools included

3,000 practice questions

3,000 exam-style questions per exam, organized topic by topic in sets of 25. Every answer explained, with the rule it comes from.

6 full mock exams

6 full-length timed mock exams per exam, with real question counts and time limits, so test day feels like practice day.

Exam Readiness Score

One 0 to 100 number that tells you when you're ready to book. Reach 80 and you're covered by our Pass Guarantee.

800 flashcards + spaced repetition

800 flashcards per exam, in a deck for each topic, that come back right before you'd forget them. Five minutes a day keeps every number fresh.

60 comprehensive key notes

60 key notes per exam, split across its topics and each explained in full: the concepts, worked exam examples, the traps examiners use and a quick recap. Your first set is free with an account.

Mind maps

See the whole exam on one screen: every topic and the facts under it.

Sample questions with answers

These are the questions in the free test above, with answers. Try the test first. You'll learn more by getting some wrong.

1. A mill replaces ingot casting with continuous casting for steel billets. Which discontinuity problem is the change most likely to remove?
Answer: Top-end shrinkage pipe that had to be cropped from each ingot. An ingot shrinks into a deep pipe at its top, and that part is cropped and scrapped; continuous casting feeds liquid steel steadily and avoids that end loss. The other three options are typical of continuous casting itself, so changing to it will not remove them. Rule: compare ingot and concast by where shrinkage goes, then by which discontinuities each route introduces.
2. A probability of detection study for a manual UT procedure reports an a90/95 value of 2.0 mm. What does this mean?
Answer: There is 95% confidence that 2.0 mm flaws are found with at least 90% probability. An a90/95 value is the flaw size for which detection probability is at least 90%, stated with 95% statistical confidence. It says nothing directly about false calls, the share of inspectors, or guaranteed detection. Rule: read the first number as the detection probability and the second as the confidence in that estimate.
3. A deep, narrow submerged arc bead with a depth-to-width ratio near 1.5, in steel with relatively high sulphur, cracks along its centreline as it cools. What type of cracking is this?
Answer: Solidification (hot) cracking. A high depth-to-width ratio concentrates low-melting segregates at the centreline, and sulphur makes it worse, so the bead tears as it solidifies. Hydrogen cracks are delayed and sit mainly in the heat-affected zone. Rule: centreline cracks appearing during cooling point to solidification, so reduce depth-to-width ratio and control sulphur.
4. An initial CSWIP Level 3 candidate passes every section except Section E, where the mark is 65%. What retest route does CSWIP-ISO-NDT-11/93-R give?
Answer: Up to two retests of Section E within one year, not within 30 days unless further training is done. An initial candidate may take two retests of the failed sections, completed within one year of the initial test, or must repeat the whole examination. A retest cannot be taken within 30 days of the previous attempt unless further specific training is undertaken. Rule: retest only what failed, count the two attempts and watch the one-year limit.
5. A low-carbon steel shaft is magnetised with a head shot. Particles are applied only after the current stops, and no indications appear. What is the main weakness of this test?
Answer: Low-carbon steel retains little field, so use the continuous method. The residual method relies on field left in the part, and low-carbon steel has low retentivity, so little flux leaks at a crack after the current stops. Apply particles while the current flows, using the continuous method, for such materials. Rule: use the residual method only on high-retentivity materials and only where the specification allows it.
6. Penetrant testing to ISO 3452-1 is needed on site, and the test surface is at 4 °C. The available system is qualified only for 10 °C to 50 °C. What should the Level 3 instruct?
Answer: Test to ISO 3452-6 with a system qualified for that low temperature. ISO 3452-1 sets 10 °C to 50 °C as the normal range, and outside it the testing must follow ISO 3452-5 or ISO 3452-6, using materials qualified for that condition. Simply extending the dwell does not qualify the system. Rule: temperature is a qualification limit, not a setting the inspector can adjust on site.
7. Direct visual testing of a fusion weld to ISO 17637 is done at 300 lx, with the eye 500 mm from the surface and viewing at 45° to it. What is the position?
Answer: Not acceptable: illuminance is below the 350 lx minimum. ISO 17637 requires at least 350 lx at the surface and recommends 500 lx. The eye must be within 600 mm of the surface and at no less than 30°, so the 500 mm and 45° viewing are fine, but the lighting fails. Rule: check illuminance, distance and angle separately, and measure the lighting at the test surface.
8. With the same probe and at the same far-field range, by how many decibels would a 6 mm flat-bottomed hole echo exceed a 3 mm flat-bottomed hole echo?
Answer: 12 dB. Echo amplitude from a small disc reflector is proportional to its area, so doubling the diameter quadruples the amplitude: 20 log 4 = 12 dB. The 6 dB answer treats amplitude as proportional to diameter. Rule: flat-bottomed hole amplitude scales with diameter squared, but a side-drilled hole scales with the square root of its diameter.
9. A 168 mm diameter steel pipe weld has no internal access and is radiographed by the double-wall single-image technique. Which part of the weld is assessed on each image?
Answer: Only the wall next to the film or detector. In double-wall single-image work, the source-side wall is blurred by its large object-to-film distance, so only the film-side wall can be interpreted. That is why several exposures are needed around the circumference. Rule: double-wall single-image means one wall assessed per image, the one nearest the film or detector.
10. A thermal camera is set to an emissivity of 0.95 and views a bright, polished aluminium busbar at 80 °C in a 20 °C room. What will the reading most likely show?
Answer: Far below the true temperature, because the surface mostly reflects the room. Polished aluminium has a very low emissivity, so it emits little and mostly reflects the 20 °C surroundings, and a camera set to 0.95 reads far too low. Thermal conductivity does not fix the error. Rule: raise the emissivity with paint or tape, or set the correct value, before trusting a thermal reading on bright metal.
11. A linear phased array is in direct contact with steel (longitudinal velocity 5,900 m/s), with an element pitch of 1.0 mm and a beam steered 30° from the normal. What delay is needed between adjacent elements?
Answer: 85 ns. Delay = pitch x sin(angle) ÷ velocity = 0.0010 x 0.5 ÷ 5,900 = 8.5 x 10^-8 s, about 85 ns. Leaving out the sine gives 170 ns and using the cosine gives 147 ns. Rule: steering delay depends on the pitch projected along the wavefront, so use the sine of the steering angle.
12. A TOFD setup has a probe centre separation of 80 mm on steel (longitudinal velocity 5,920 m/s). A flaw tip signal arrives 3.38 µs after the lateral wave. If the tip is midway between the probes, how deep is it?
Answer: 30 mm. The extra path is 3.38 x 5.92 = 20 mm, so the tip path is 100 mm, or 50 mm per leg. With half the separation at 40 mm, depth = root(50² - 40²) = 30 mm. Taking the 20 mm extra path as the depth is the usual error. Rule: find the total path first, then apply Pythagoras with half the probe separation.
13. A contract specifies ISO 5817 quality level B for a full-penetration ferritic steel butt weld and calls for ultrasonic testing. Using the ISO 17635 correlation, which combination applies?
Answer: Testing level at least B to ISO 17640 and acceptance level 2 to ISO 11666. The correlation links quality level B to UT testing level at least B and acceptance level 2, while quality level C links to testing level at least A and acceptance level 3. ISO 10675-1 is for radiography and ISO 23278 is for magnetic particle testing. Rule: read the quality level first, then the correlation table, and confirm the edition named in the contract.
14. A narrow-gap butt weld has near-vertical fusion faces, and lack of side-wall fusion is the main concern. Which UT arrangement is best suited to detecting it?
Answer: Tandem pitch-catch probes aimed to reflect from the fusion face. A near-vertical planar flaw reflects sound away from a single pulse-echo probe, so a tandem arrangement places a second probe to catch the specular reflection. Pulse-echo 45° and 0° scans meet the face at poor angles, and creeping waves only cover the near surface. Rule: choose a technique that delivers the reflected energy back to a receiver for the expected flaw orientation.
15. A candidate's draft UT procedure for a 20 mm butt weld says only: 'Use a suitable angle probe.' Which rewrite best meets the purpose of a Level 3 procedure?
Answer: Use a 4 MHz, 60° shear-wave probe, demonstrated on the stated reference block. A procedure must give instructions another qualified person can repeat, so it names the frequency, angle, wave mode and reference standard. Leaving the choice to the operator on the day defeats the purpose of Level 3 approval. Rule: replace every vague word such as 'suitable' with a value or a stated condition that can be checked.

Get the full CSWIP NDT Level 3 prep

Most popular · cancel anytime

Premium Monthly

$147/month
per exam
About $4.83 a day · less than a retake fee, for the certification that lets you approve procedures and certify technicians
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.

Best value · 3 months free

Premium Yearly

$1,323/year
per exam
Pay for 9 months, get 12. Save $441 against paying monthly.
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.

Pass Guarantee. Complete the full prep, sit your exam within 60 days, and if you don't pass we refund 100% of your subscription payments. See the requirements
Secure checkout by Stripe Card, Apple Pay, Google Pay Pass Guarantee

CSWIP NDT Level 3 exam FAQ

How many questions are on the CSWIP NDT Level 3 exam?

Basic examination: Section A 25, Section B 10 and Section C 60 multiple-choice questions. Main Method examination: Section D 30 and Section E 20 multiple-choice questions, plus Section F, drafting one NDT procedure, with a time limit of section a 50 minutes; section b 30 minutes; section c 120 minutes; section d 60 minutes; section e 60 minutes; section f 5 hours. Format: section b may be open book. section e may be open book for questions on codes, standards and specifications. section f is a written procedure, with applicable codes, standards and specifications allowed. rules for the other sections are not published; confirm with twi certification. this prep covers only the written knowledge sections, using 4-option single-best-answer practice items; it does not cover the level 2 practical required of candidates without level 2, or mark your section f procedure.

What is the passing score for CSWIP NDT Level 3?

At least 70% in each section of the examination.

How much does the CSWIP NDT Level 3 exam cost?

Not published by TWI Certification on its scheme pages; confirm with TWI Certification or your test centre. ASNT fees differ for members and nonmembers and can change, so confirm on the ASNT certification website before you apply.

Which languages is the CSWIP NDT Level 3 exam offered in?

Not published by TWI Certification; confirm with TWI Certification or your test centre.

Where do I take the CSWIP NDT Level 3 exam?

TWI Certification test centres in the UK and overseas. Delivery format (paper or computer) is not published in the scheme document; confirm with TWI Certification.

Is this CSWIP NDT Level 3 practice test free?

Yes. The 15-question practice test on this page is free, with an explanation for every answer and no signup. A free account also unlocks the complete study notes for the first topic. The full CSWIP NDT Level 3 prep is Premium at $147 a month for this exam.

What's in the premium CSWIP NDT Level 3 prep?

3,000 practice questions organized topic by topic (Section A: Materials and Process Technology: 375; Section A: Discontinuities and Failure Modes: 375; Section B: CSWIP Scheme, ISO 9712 and SNT-TC-1A: 375; Section C: MT, PT and VT at Level 2: 375; Section C: UT, RT, ET, AE and TIR at Level 2: 375; Section D: Level 3 Main Method Knowledge: 375; Section E: Application, Codes and Standards: 375; Section F: Procedure Writing: 375), 6 full-length timed mock exams of 50 questions, 800 flashcards and 60 comprehensive key notes split across all 8 topics, plus a mistakes bank and the Readiness Score.

Related practice tests

Exam details are summarized from the official candidate information available in October 2026. ASNT changes formats and fees, so confirm with TWI Certification Ltd (CSWIP) before you book. NDTLevel3Exam is not affiliated with ASNT or Pearson VUE.

Start the free test