Try the full study dashboard free, no signup: practice, flashcards and your Exam Readiness Score. Open it →
Home / Study guides / CSWIP NDT Level 3
Study guide · Last updated November 2026

CSWIP NDT Level 3 Exam Study Guide (2026)

Everything the CSWIP NDT Level 3 (CSWIP-ISO-NDT-11/93-R) tests, topic by topic: what each section covers, the facts that come up most, and how to study it. Pair it with the free 15-question practice test.

The exam at a glance

QuestionsBasic examination: Section A 25, Section B 10 and Section C 60 multiple-choice questions. Main Method examination: Section D 30 and Section E 20 multiple-choice questions, plus Section F, drafting one NDT procedure
TimeSection A 50 minutes; Section B 30 minutes; Section C 120 minutes; Section D 60 minutes; Section E 60 minutes; Section F 5 hours
Passing scoreAt least 70% in each section of the examination
FormatSection B may be open book. Section E may be open book for questions on codes, standards and specifications. Section F is a written procedure, with applicable codes, standards and specifications allowed. Rules for the other sections are not published; confirm with TWI Certification. This prep covers only the written knowledge sections, using 4-option single-best-answer practice items; it does not cover the Level 2 practical required of candidates without Level 2, or mark your Section F procedure
Certifying bodyTWI Certification Ltd (CSWIP)
Test providerTWI Certification test centres in the UK and overseas. Delivery format (paper or computer) is not published in the scheme document; confirm with TWI Certification

Mind map: the whole exam on one screen

CSWIP NDT Level 3
Section A: Materials and Process Technology
Purpose of cropping an ingot topNormalising cooling mediumProcess that forms sheet and strip after hot rollingWhy extrusion may be used instead of rolling or forging
Section A: Discontinuities and Failure Modes
Casting flaw caused by metal streams failing to fuseTypical location of a hot tearForging flaw from working too coldFailure mode showing beach marks
Section B: CSWIP Scheme, ISO 9712 and SNT-TC-1A
Level 3 experience for UT from Level 2 without higher educationLevel 3 experience for PT from Level 2 with higher educationCertification validity from the certification decisionCSWIP near-vision standard
Section C: MT, PT and VT at Level 2
6 key facts
Section C: UT, RT, ET, AE and TIR at Level 2
6 key facts
Section D: Level 3 Main Method Knowledge
7 key facts
Section E: Application, Codes and Standards
6 key facts
Section F: Procedure Writing
6 key facts
Free with an account

Read the complete CSWIP NDT Level 3 study notes for “Section A: Materials and Process Technology”

Our first full set of comprehensive notes, about 15 minutes of reading: From liquid steel to semi-finished product · Casting routes · Wrought routes · Heat treatment · Machining, finishing and quality statistics, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.

Open the free dashboard

1. Section A: Materials and Process Technology

Section A: 25 multiple-choice questions on materials, processes and discontinuities, in 50 minutes, 70% to pass (no split published within the section). The UT appendix lists ingot and concast production, casting, forging, rolling, extrusion, heat treatment, machining, finishing, non-metals and metrology.

Key facts

  • Ingot casting uses narrow-end-up or wide-end-up moulds. Ingots are then hot worked by rolling, forging or extrusion, and the top with the shrinkage pipe is cropped.
  • Continuous casting feeds liquid steel into a water-cooled mould and avoids ingot end losses, but it has its own centreline and surface discontinuities.
  • Rolling takes blooms, slabs and billets through primary and secondary stages to sections, plate, sheet and strip.
  • Forging may be open-die, press or closed-die; extrusion suits long, constant sections that are hard to roll or forge.
  • Annealing softens, normalising air-cools to refine grain, and stress relieving reduces residual stress below the critical range.
  • Machining includes turning, boring, milling, grinding and electrochemical removal. Finishing includes shot peening, grit blasting, painting, plating and chemical conversion coating.
  • The syllabus also includes non-metals and composite processing, dimensional metrology, statistical process control and probability of detection.

Flashcards

Purpose of cropping an ingot topTo remove the shrinkage pipe and segregated metal.
Normalising cooling mediumStill air.
Process that forms sheet and strip after hot rollingCold rolling.
Why extrusion may be used instead of rolling or forgingIt makes long, constant, often complex sections in one pass.

Exam tip: With 2 minutes per question, reason from the process: where the heat, deformation or shrinkage occurred tells you what the part will look like and where its flaws are.

2. Section A: Discontinuities and Failure Modes

The discontinuity and failure part of Section A. Syllabus items include casting defects (shrinkage, inclusions, cold shuts, porosity, laps, hot tears, cracks), rolling and forging defects (bursts, laps, seams, cracks) and failure modes.

Key facts

  • Casting defects: shrinkage at hot spots, gas porosity, inclusions, cold shuts where metal streams meet, laps, and hot tears at restrained section changes.
  • Rolling defects include laminations, stringers and seams that follow the rolling direction.
  • Forging defects include bursts, laps, seams and cracks, usually from working the metal too cold or too hard.
  • Weld defects include solidification cracking, hydrogen cracking, lack of fusion, incomplete penetration, porosity, slag and undercut.
  • Failure modes include overload, fatigue, creep, stress corrosion cracking, hydrogen damage and corrosion.
  • Orientation matters: rolling and forging align discontinuities, so test directions should be selected to meet them.

Flashcards

Casting flaw caused by metal streams failing to fuseCold shut.
Typical location of a hot tearAt a restrained section change.
Forging flaw from working too coldA burst.
Failure mode showing beach marksFatigue.

Exam tip: Link every discontinuity to the production step that makes it and to its usual orientation; that is what the question is usually testing.

3. Section B: CSWIP Scheme, ISO 9712 and SNT-TC-1A

Section B: 10 multiple-choice questions on the certification body's certification and qualification system, in 30 minutes, 70% to pass, and may be open book. The appendices list BS EN ISO 9712 and SNT-TC-1A.

Key facts

  • CSWIP-ISO-NDT-11/93-R is the governing document, and the 11th Edition is dated July 2026. Each method's Appendix 1 part sets the syllabus and exam details.
  • Level 3 experience for AT, ET, LT, RT, TT and UT: 450 days from Level 2, 270 days from Level 2 with higher education, and 540 days for direct access with higher education.
  • Level 3 experience for MT, PT, ST and VT: 240 days, 180 days and 360 days on the same three routes.
  • A day of experience is at least 7 and at most 12 hours. Adding a method may reduce required experience by 25%.
  • Near vision must be tested annually after certification. Colour vision evidence must be from the previous five calendar years, using the Ishihara 24-plate test.
  • A certificate is valid for five years from the certification decision, and can be renewed for a further five years.
  • Ten-year Level 3 recertification uses 20 method application questions and 10 scheme questions, plus the Level 2 recertification practical unless a valid Level 2 of the same scope is held, or structured credit.

Flashcards

Level 3 experience for UT from Level 2 without higher education450 days.
Level 3 experience for PT from Level 2 with higher education180 days.
Certification validity from the certification decisionFive years.
CSWIP near-vision standardN4.5 Times Roman or Jaeger 1 (or equivalent) at not less than 30 cm, corrected or unaided, with one or both eyes.

Exam tip: Section B may be open book, but it has only 10 questions and needs 70%, so know the scheme layout and tables well enough to find answers fast.

Test yourself on these topics

Take the free 15-question CSWIP NDT Level 3 test, then save your results to unlock your Readiness Score and the mistakes bank.

Start the free test

4. Section C: MT, PT and VT at Level 2

Part of Section C: 60 multiple-choice questions in 120 minutes on at least four methods of your choice, 15 each, at Level 2 standard, and one method must be UT or RT. Principles, technique selection, equipment, application and interpretation.

Key facts

  • MT uses a field at 90° to the expected discontinuity. Yokes give longitudinal fields, and current through a part gives circular fields.
  • The continuous method applies particles while the field is on; the residual method relies on high retentivity.
4 more key facts, 8 key notes, 100 flashcards and 375 practice questions for this topic are in premium.

Flashcards

Field created by a yokeLongitudinal, between its poles.

Exam tip: Choose the four methods you use at work. For each one, learn its standard limits, because those numbers appear in technique questions.

5. Section C: UT, RT, ET, AE and TIR at Level 2

The rest of Section C, at Level 2 standard. The scheme names MT, PT, RT, UT, ET, VT, AE and TIR as methods for this section; one of your four methods must be UT or RT.

Key facts

  • UT reflectors: flat-bottomed holes scale with area, and side-drilled holes scale with the square root of diameter.
  • RT double-wall single-image assesses only the film-side wall, so several exposures are needed.
4 more key facts, 7 key notes, 100 flashcards and 375 practice questions for this topic are in premium.

Flashcards

Amplitude change per doubling of side-drilled hole diameterAbout +3 dB.

Exam tip: Section C needs broad recall. Rule methods in or out by material, access and flaw orientation before you get into the details.

6. Section D: Level 3 Main Method Knowledge

Section D: 30 multiple-choice questions in 60 minutes, 70% to pass, on Level 3 knowledge of your main method. For UT, this covers the Level 1 and 2 syllabus at greater depth, plus twin-crystal and focused probes, immersion, gap scanning, TOFD, phased array, guided waves, digital processing and flaw sizing.

Key facts

  • Twin-crystal probes separate transmit and receive to reduce near-surface dead zone.
  • Focused probes concentrate sound and improve lateral resolution within their focal range.
5 more key facts, 7 key notes, 100 flashcards and 375 practice questions for this topic are in premium.

Flashcards

Main benefit of a twin-crystal probeBetter near-surface resolution.

Exam tip: Set up each Section D calculation carefully, and read the question for the geometry first; most of the wrong answers come from using the wrong dimension.

7. Section E: Application, Codes and Standards

Section E: 20 multiple-choice questions in 60 minutes on applying the method in your sector, 70% to pass, and may be open book for code, standard and specification questions. UT sectors are Welds, Castings and Wrought Products (including forgings).

Key facts

  • Select the sector you actually work in, as the questions are tied to that sector's products and standards.
  • ISO 17635 links ISO 5817 quality levels to testing levels and acceptance levels for each NDT method.
4 more key facts, 7 key notes, 100 flashcards and 375 practice questions for this topic are in premium.

Flashcards

Standard linking quality level, testing level and acceptance levelISO 17635.

Exam tip: Open-book questions still eat time. Practise finding clauses and tables quickly in the standards you actually bring.

8. Section F: Procedure Writing

A written task, not multiple choice: 5 hours to draft an NDT procedure for a component chosen by the examiner, 70% to pass, and applicable codes, standards and specifications may be used. Practice items here build procedure judgement.

Key facts

  • The examiner chooses the component, so practise reading drawings and specifications quickly.
  • A good procedure identifies scope, referenced documents, personnel, equipment, calibration, technique, sensitivity, scanning, evaluation and reporting.
4 more key facts, 7 key notes, 100 flashcards and 375 practice questions for this topic are in premium.

Flashcards

Time allowed for Section F5 hours.

Exam tip: Check each technical sentence with one question: could a Level 2 follow it and get the same result? If not, add the missing value.

How to pass

  • Download the Appendix 1 part for your method, because it sets the sector options and the syllabus. For UT, the sectors are Welds, Castings and Wrought Products (including forgings).
  • Section C is 60 of the 145 multiple-choice questions. You choose at least four methods, 15 questions each, and one must be UT or RT, so pick the four you can answer at Level 2 depth.
  • Sections A and C both allow 2 minutes per question, and each needs 70% on its own, so a strong Section C cannot rescue a weak Section A. Once you pass Sections A, B and C, you do not resit them for later Level 3 methods.
  • After a failure you may take two retests of the failed sections within one year of the initial test, and not within 30 days unless you complete further specific training. Book retests with that window in mind.

Frequently asked questions

How long should I study for the CSWIP NDT Level 3 exam?

Most working candidates need 4 to 8 weeks at 45 to 60 minutes a day. Book your exam once your Readiness Score has stayed at 80 or higher for about a week.

Can I take the CSWIP NDT Level 3 exam online?

No. ASNT NDT Level III exams are taken in person, on a computer, at Pearson VUE test centers or ASNT Authorized Exam Centers. Format: section b may be open book. section e may be open book for questions on codes, standards and specifications. section f is a written procedure, with applicable codes, standards and specifications allowed. rules for the other sections are not published; confirm with twi certification. this prep covers only the written knowledge sections, using 4-option single-best-answer practice items; it does not cover the level 2 practical required of candidates without level 2, or mark your section f procedure. Check ASNT's current exam information for the rules.

What score do I need to pass the CSWIP NDT Level 3 exam?

At least 70% in each section of the examination. The exam has basic examination: section a 25, section b 10 and section c 60 multiple-choice questions. main method examination: section d 30 and section e 20 multiple-choice questions, plus section f, drafting one ndt procedure and a time limit of section a 50 minutes; section b 30 minutes; section c 120 minutes; section d 60 minutes; section e 60 minutes; section f 5 hours.

What are the most tested topics?

The outline covers section a: materials and process technology, section a: discontinuities and failure modes, section b: cswip scheme, iso 9712 and snt-tc-1a, section c: mt, pt and vt at level 2, section c: ut, rt, et, ae and tir at level 2, section d: level 3 main method knowledge, section e: application, codes and standards, section f: procedure writing. Use the free practice test to see which ones you need most.

The premium CSWIP NDT Level 3 study path

Premium CSWIP NDT Level 3 prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.

3,000practice questions, every answer explained
6full-length mock exams, 50 questions each, timed
800flashcards with spaced repetition, sorted by topic
60comprehensive key notes across 8 topics

Your step-by-step study path

  1. 1
    Section A: Materials and Process Technology8 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Notes free with an account
  2. 2
    Section A: Discontinuities and Failure Modes8 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  3. 3
    Section B: CSWIP Scheme, ISO 9712 and SNT-TC-1A8 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  4. 4
    Section C: MT, PT and VT at Level 28 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  5. 5
    Section C: UT, RT, ET, AE and TIR at Level 27 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  6. 6
    Section D: Level 3 Main Method Knowledge7 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  7. 7
    Section E: Application, Codes and Standards7 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  8. 8
    Section F: Procedure Writing7 key notes, 100 flashcards, then 375 practice questions in 15 sets of 25
    Premium
  9. Final step: 6 full mock exams50 questions each, timed like test day. Pass them, then book your exam.
    Premium

Get every note, flashcard and question

Most popular · cancel anytime

Premium Monthly

$147/month
per exam
About $4.83 a day · less than a retake fee, for the certification that lets you approve procedures and certify technicians
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.

Best value · 3 months free

Premium Yearly

$1,323/year
per exam
Pay for 9 months, get 12. Save $441 against paying monthly.
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.

Pass Guarantee. Complete the full prep, sit your exam within 60 days, and if you don't pass we refund 100% of your subscription payments. See the requirements
Secure checkout by Stripe Card, Apple Pay, Google Pay Pass Guarantee

Summarized from ASNT's official candidate information and the rules cited, checked October 2026. Confirm current requirements with TWI Certification Ltd (CSWIP).

Start the free test