Try the full study dashboard free, no signup: practice, flashcards and your Exam Readiness Score. Open it →
Home / Practice tests / AE Level III
ASNT · Last updated November 2026

ASNT NDT Level III Acoustic Emission Testing (AE): free practice test

The ASNT Level III acoustic emission method exam: 135 questions in 4 hours. ASNT's outline has four areas: instrumentation and signal processing, AE test techniques (setup, loading, noise, interpretation, evaluation and reports), codes, standards, procedures and societies, and applications. AE is not one of ASNT's ANAB-accredited Level III methods.

Watch the free 4:13 video lesson: the key AE Level III concepts →

Premium: 3,000 practice questions, 6 full mock exams, 800 flashcards and 60 comprehensive key notes, topic by topic. See the study path ·

Or open the free AE Level III study dashboard: flashcards, notes and your Readiness Score, no signup →

About the AE Level III exam

The ASNT Level III acoustic emission method exam: 135 questions in 4 hours. ASNT's outline has four areas: instrumentation and signal processing, AE test techniques (setup, loading, noise, interpretation, evaluation and reports), codes, standards, procedures and societies, and applications. AE is not one of ASNT's ANAB-accredited Level III methods.

What's on the exam

AE Level III
AE Principles, Sources and Wave Propagation
7 key facts
Sensors, Cables and Signal Conditioning
7 key facts
Signal Detection, Processing and Source Location
7 key facts
Equipment Selection, Calibration and Loading
7 key facts
Noise, Data Display, Interpretation and Evaluation
7 key facts
Codes, Standards, Procedures and Societies
6 key facts
Applications of Acoustic Emission Testing
7 key facts

Each branch is a topic in the official outline. Members see every key fact on the full mind map. Read the free study guide →

How to pass the AE Level III exam

  • 135 questions in 4 hours is about 106 seconds each. Keep the dB, location and Felicity ratio arithmetic quick so you have time for the long scenario stems.
  • Learn the hit features (amplitude, counts, duration, rise time, energy) and which of them depend on the threshold. Many questions turn on that.
  • Know the timing parameters: peak definition time, hit definition time and hit lockout time, and what goes wrong when each is set too short or too long.
  • Know which ASME Section V article covers which job: FRP vessels, metallic vessels during pressure testing, and continuous monitoring.

Save your results and get your Readiness Score

Create a free account after the test: your score by topic, a mistakes bank, the complete study notes for the first topic, flashcards and the NDT Level III Formula Sheet.

Take the test first

What's in the premium AE Level III prep

Premium AE Level III prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.

3,000practice questions, every answer explained
6full-length mock exams, 135 questions each, timed
800flashcards with spaced repetition, sorted by topic
60comprehensive key notes across 7 topics

Your step-by-step study path

  1. 1
    AE Principles, Sources and Wave Propagation9 key notes, 115 flashcards, then 450 practice questions in 18 sets of 25
    Notes free with an account
  2. 2
    Sensors, Cables and Signal Conditioning9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  3. 3
    Signal Detection, Processing and Source Location9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  4. 4
    Equipment Selection, Calibration and Loading9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  5. 5
    Noise, Data Display, Interpretation and Evaluation8 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  6. 6
    Codes, Standards, Procedures and Societies8 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  7. 7
    Applications of Acoustic Emission Testing8 key notes, 110 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  8. Final step: 6 full mock exams135 questions each, timed like test day. Pass them, then book your exam.
    Premium
Free with an account

Read the complete AE Level III study notes for “AE Principles, Sources and Wave Propagation”

Our first full set of comprehensive notes, about 15 minutes of reading: What acoustic emission is · Load history: Kaiser and Felicity · Wave propagation · Frequency and sensor choice, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.

Open the free dashboard

Study tools included

3,000 practice questions

3,000 exam-style questions per exam, organized topic by topic in sets of 25. Every answer explained, with the rule it comes from.

6 full mock exams

6 full-length timed mock exams per exam, with real question counts and time limits, so test day feels like practice day.

Exam Readiness Score

One 0 to 100 number that tells you when you're ready to book. Reach 80 and you're covered by our Pass Guarantee.

800 flashcards + spaced repetition

800 flashcards per exam, in a deck for each topic, that come back right before you'd forget them. Five minutes a day keeps every number fresh.

60 comprehensive key notes

60 key notes per exam, split across its topics and each explained in full: the concepts, worked exam examples, the traps examiners use and a quick recap. Your first set is free with an account.

Mind maps

See the whole exam on one screen: every topic and the facts under it.

Sample questions with answers

These are the questions in the free test above, with answers. Try the test first. You'll learn more by getting some wrong.

1. A vessel was last loaded to 2.0 MPa. On reloading, significant emission starts at 1.7 MPa. What is the Felicity ratio and what does it suggest?
Answer: 0.85: the Kaiser effect has broken down, suggesting damage. Felicity ratio = load at onset of significant emission ÷ previous maximum load = 1.7 ÷ 2.0 = 0.85. A ratio below 1 means emission began before the previous maximum, which is the Felicity effect and a sign of damage. Inverting the ratio gives 1.18.
2. AE from a source in a thin steel plate travels mainly as Lamb (plate) waves. At low frequency-thickness, which statement is correct?
Answer: The extensional mode arrives first; the flexural mode is slower. At low frequency-thickness the extensional (symmetric) mode travels near the plate velocity and arrives first, while the flexural (antisymmetric) mode is slower and strongly dispersive. Which mode triggers each channel affects location accuracy.
3. A preamplifier with 40 dB gain outputs a 0.1 V peak signal. What is the peak amplitude in dBAE (0 dB = 1 µV at the sensor)?
Answer: 60 dBAE. Remove the preamplifier gain: 0.1 V ÷ 100 = 1 mV at the sensor. 20 × log(1 mV ÷ 1 µV) = 20 × 3 = 60 dBAE. Forgetting to remove the gain gives 100 dBAE.
4. AE sensors must monitor a pipe running at 400 °C, well above the sensors' rated temperature. What is the usual solution?
Answer: Mount the sensor on the cool end of a metal waveguide fixed to the pipe. A waveguide (a metal rod welded or clamped to the hot surface) carries the AE to a sensor kept within its rated temperature. It adds attenuation and some distortion, so verify sensitivity with lead breaks. Couplant cannot protect the sensor from 400 °C.
5. Two sensors are 2.0 m apart on a long pipe. The wave speed is 3000 m/s, and a hit reaches sensor 1 0.4 ms before sensor 2. Where is the source?
Answer: 0.4 m from sensor 1. Distance from sensor 1 = (D − V × Δt) ÷ 2 = (2.0 − 3000 × 0.0004) ÷ 2 = 0.4 m. The value V × Δt ÷ 2 = 0.6 m is the offset from the midpoint, not from the sensor.
6. On a small, highly reverberant part, the hit definition time is set much too long. What happens to the data?
Answer: Separate events are merged into one long hit. The hit ends only when no threshold crossing occurs for the hit definition time. If it is too long, reverberation and later events are lumped into one hit, inflating duration and counts. If it is too short, one event is split into several hits.
7. The fixed detection threshold is raised from 40 dB to 45 dB with all else unchanged. For a hit that still crosses threshold, which feature does not change?
Answer: Peak amplitude. Peak amplitude is the largest excursion of the waveform, independent of threshold. Counts, duration and rise time are all measured from threshold crossings, so they shrink as the threshold rises. Energy measured above threshold also changes.
8. In a system performance check, one channel's pencil lead break response is 8 dB below the others at the same distance. What should be done first?
Answer: Remount and recouple the sensor, then repeat the lead breaks. A low response usually means poor coupling or a faulty sensor, cable or preamplifier. Fix the mounting and repeat the check; replace the sensor if it stays low. Adjusting threshold or gain hides the fault and changes the test sensitivity the procedure set.
9. During a pressure test, AE continues at a steady rate through a load hold. What does this usually indicate?
Answer: Active damage or leakage that needs evaluation. Load holds are built into test procedures because sound material goes quiet when load stops rising. Continuing emission during a hold points to active damage growth, creep or a leak, and the codes use hold-period activity as an evaluation criterion.
10. Several channels record hits with very fast rise times that arrive at all sensors at the same instant, whatever the sensor spacing. What is the likely source?
Answer: Electromagnetic interference. Stress waves take time to travel, so arrival times depend on distance. Simultaneous arrival at all channels means an electrical signal, such as welding, switching or radio interference. Differential sensors, good grounding and shielding reduce it.
11. A vessel is tested next to a running pump. Which setup best rejects pump noise while keeping sensitivity on the vessel?
Answer: Guard sensors near the pump, rejecting hits that reach a guard first. Guard sensors placed between the noise source and the test zone flag hits that arrive at the guard before the data sensors, so those hits are rejected. Raising thresholds across the board also discards real AE from the vessel.
12. On a duration-versus-amplitude plot, a cluster of hits shows long duration but low amplitude. What are they most typical of?
Answer: Mechanical rubbing or friction. Friction and rubbing produce long, low-amplitude signals with slow rise. Crack growth and fiber breaks give short, sharp bursts with higher amplitude for their duration. Electrical spikes are very short with near-zero rise time.
13. A client wants AE examination of a fiber-reinforced plastic tank during its pressure test. Which ASME Section V article applies?
Answer: Article 11. Article 11 covers AE of fiber-reinforced plastic vessels during pressure testing. Article 12 covers metallic vessels during pressure testing and Article 13 covers continuous AE monitoring. Article 10 is leak testing.
14. Which ASTM standard guide describes using a pencil lead break (Hsu-Nielsen source) to check the reproducibility of AE sensor response?
Answer: ASTM E976. ASTM E976 is the guide for determining the reproducibility of AE sensor response, using a simulated source such as a pencil lead break. E1316 is terminology, E569 covers AE monitoring of structures during stimulation, and E1067 covers FRP tanks and vessels.
15. Why is AE well suited to the pressure test of a large insulated sphere?
Answer: It monitors the whole vessel from fixed sensors and finds active sources. AE listens to the whole structure through a few sensors, so most insulation can stay in place, and it reports sources active under load. It cannot size flaws or find dormant ones, so located sources are followed up with UT or other methods.

Get the full AE Level III prep

Most popular · cancel anytime

Premium Monthly

$147/month
per exam
About $4.83 a day · less than a retake fee, for the certification that lets you approve procedures and certify technicians
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.

Best value · 3 months free

Premium Yearly

$1,323/year
per exam
Pay for 9 months, get 12. Save $441 against paying monthly.
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.

Pass Guarantee. Complete the full prep, sit your exam within 60 days, and if you don't pass we refund 100% of your subscription payments. See the requirements
Secure checkout by Stripe Card, Apple Pay, Google Pay Pass Guarantee

AE Level III exam FAQ

How many questions are on the AE Level III exam?

135 multiple-choice questions, with a time limit of 4 hours. Format: closed book, computer-based, with an on-screen calculator. no practical exam. you must also pass the ndt basic exam to be certified.

What is the passing score for AE Level III?

Not published per exam. Aim for 80% or higher in practice (ASNT says its criterion-referenced cut scores are typically 70% to 80%).

How much does the AE Level III exam cost?

US$545 for ASNT members, US$625 for nonmembers (retake US$475 / US$555). ASNT fees differ for members and nonmembers and can change, so confirm on the ASNT certification website before you apply.

Which languages is the AE Level III exam offered in?

English (an online NDT terminology translation dictionary is available).

Where do I take the AE Level III exam?

Pearson VUE test centers and ASNT Authorized Exam Centers (in person, computer-based).

Is this AE Level III practice test free?

Yes. The 15-question practice test on this page is free, with an explanation for every answer and no signup. A free account also unlocks the complete study notes for the first topic. The full AE Level III prep is Premium at $147 a month for this exam.

What's in the premium AE Level III prep?

3,000 practice questions organized topic by topic (AE Principles, Sources and Wave Propagation: 450; Sensors, Cables and Signal Conditioning: 425; Signal Detection, Processing and Source Location: 425; Equipment Selection, Calibration and Loading: 425; Noise, Data Display, Interpretation and Evaluation: 425; Codes, Standards, Procedures and Societies: 425; Applications of Acoustic Emission Testing: 425), 6 full-length timed mock exams of 135 questions, 800 flashcards and 60 comprehensive key notes split across all 7 topics, plus a mistakes bank and the Readiness Score.

Related practice tests

Exam details are summarized from the official candidate information available in October 2026. ASNT changes formats and fees, so confirm with ASNT Certification Services LLC (American Society for Nondestructive Testing) before you book. NDTLevel3Exam is not affiliated with ASNT or Pearson VUE.

Start the free test