Try the full study dashboard free, no signup: practice, flashcards and your Exam Readiness Score. Open it →
Home / Practice tests / ASNT NDT Level II MT
ASNT · Last updated November 2026

ASNT NDT Level II, Magnetic Particle Testing (MT): free practice test

ASNT's third-party written certification for magnetic particle technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector, with 40 days of MT experience, 76 days of total NDT experience and 3 days of training required. The General exam moves to a revised five-domain outline for exams after 15 December 2026, which this prep follows while still covering the earlier topics. This prep covers only the written exams; the visual acuity, practical and job-specific exams are given by your employer.

Watch the free 4:26 video lesson: the key ASNT NDT Level II MT concepts →

Premium: 3,000 practice questions, 6 full mock exams, 800 flashcards and 60 comprehensive key notes, topic by topic. See the study path ·

Or open the free ASNT NDT Level II MT study dashboard: flashcards, notes and your Readiness Score, no signup →

About the ASNT NDT Level II MT exam

ASNT's third-party written certification for magnetic particle technicians: a 50-item General exam and a 40-item Specific exam for the general industry or pressure equipment sector, with 40 days of MT experience, 76 days of total NDT experience and 3 days of training required. The General exam moves to a revised five-domain outline for exams after 15 December 2026, which this prep follows while still covering the earlier topics. This prep covers only the written exams; the visual acuity, practical and job-specific exams are given by your employer.

What's on the exam

ASNT NDT Level II MT
MT Principles and Theory
7 key facts
Use and Care of MT Equipment and Accessories
7 key facts
MT Techniques and Demagnetization
7 key facts
Interpreting, Evaluating and Documenting Results
6 key facts
Codes, Standards, Specifications and Procedures
6 key facts
Specific Exam: General Industry
6 key facts
Specific Exam: Pressure Equipment
6 key facts

Each branch is a topic in the official outline. Members see every key fact on the full mind map. Read the free study guide →

How to pass the ASNT NDT Level II MT exam

  • Check your exam date against 15 December 2026. Earlier General exams use the ten-topic outline (flux fields, magnetization, demagnetization, discontinuities); later ones use five job-task domains that add daily standardizations such as lift tests, Ketos rings and QQIs.
  • ASNT publishes no cut score for this exam. The 70% per exam and 80% composite figures often quoted come from employer programs under SNT-TC-1A, so treat 80% on each exam as your practice target.
  • ASNT's public page does not name the codes behind the Specific exams. ASME Section V Article 7 and Section VIII Appendix 6 are the usual references for pressure equipment, and ASTM E1444 and E709 for general industry, so learn their numbers.
  • A passed General result stays valid for 5 years but a passed Specific result only for 2 years, so book them close together. After a failure you reapply and wait 30 days.

Save your results and get your Readiness Score

Create a free account after the test: your score by topic, a mistakes bank, the complete study notes for the first topic, flashcards and the NDT Level III Formula Sheet.

Take the test first

What's in the premium ASNT NDT Level II MT prep

Premium ASNT NDT Level II MT prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.

3,000practice questions, every answer explained
6full-length mock exams, 50 questions each, timed
800flashcards with spaced repetition, sorted by topic
60comprehensive key notes across 7 topics

Your step-by-step study path

  1. 1
    MT Principles and Theory9 key notes, 115 flashcards, then 450 practice questions in 18 sets of 25
    Notes free with an account
  2. 2
    Use and Care of MT Equipment and Accessories9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  3. 3
    MT Techniques and Demagnetization9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  4. 4
    Interpreting, Evaluating and Documenting Results9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  5. 5
    Codes, Standards, Specifications and Procedures8 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  6. 6
    Specific Exam: General Industry8 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  7. 7
    Specific Exam: Pressure Equipment8 key notes, 110 flashcards, then 425 practice questions in 17 sets of 25
    Premium
  8. Final step: 6 full mock exams50 questions each, timed like test day. Pass them, then book your exam.
    Premium
Free with an account

Read the complete ASNT NDT Level II MT study notes for “MT Principles and Theory”

Our first full set of comprehensive notes, about 15 minutes of reading: How MT works · Field direction · Magnetic properties · Current and particles, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.

Open the free dashboard

Study tools included

3,000 practice questions

3,000 exam-style questions per exam, organized topic by topic in sets of 25. Every answer explained, with the rule it comes from.

6 full mock exams

6 full-length timed mock exams per exam, with real question counts and time limits, so test day feels like practice day.

Exam Readiness Score

One 0 to 100 number that tells you when you're ready to book. Reach 80 and you're covered by our Pass Guarantee.

800 flashcards + spaced repetition

800 flashcards per exam, in a deck for each topic, that come back right before you'd forget them. Five minutes a day keeps every number fresh.

60 comprehensive key notes

60 key notes per exam, split across its topics and each explained in full: the concepts, worked exam examples, the traps examiners use and a quick recap. Your first set is free with an account.

Mind maps

See the whole exam on one screen: every topic and the facts under it.

Sample questions with answers

These are the questions in the free test above, with answers. Try the test first. You'll learn more by getting some wrong.

1. A steel ring is suspected of radial cracks on its flat faces. A central conductor is passed through the bore and energized. Will this setup detect the radial cracks?
Answer: Yes, the circular field crosses radial cracks. Current in a central conductor induces a circular field that runs around the ring, so it crosses radial cracks on the faces and axial cracks on the bore and outside surface at about 90°. Discontinuities that run around the ring, parallel to the field, would need a different field direction.
2. A hardened tool steel part gives strong indications when particles are applied after the magnetizing current is switched off. Which material property makes this residual method work?
Answer: High retentivity. Retentivity is the ability to hold residual magnetism after the magnetizing force is removed, and hardened steels have high retentivity and coercive force. Soft, high-permeability steels magnetize easily but lose most of their field, so they need the continuous method.
3. A 2 in diameter shaft must be examined for inclusions lying just below the surface, using the wet method. Which magnetizing current is the best choice?
Answer: Full-wave rectified direct current. Alternating current concentrates the field near the surface (skin effect), so it is best for surface cracks. Rectified direct current penetrates deeper and is preferred for near-surface discontinuities; with wet particles, full-wave rectified DC is the usual choice. More AC amperage does not overcome the skin effect.
4. A settling test on a visible (nonfluorescent) wet bath gives 3.0 mL of particles per 100 mL. The procedure follows the usual 1.2 to 2.4 mL range. What should be done?
Answer: Add vehicle to dilute it, then retest before use. Too high a concentration gives heavy background that masks fine indications, so the bath is diluted with clean vehicle and retested. Visible baths run 1.2 to 2.4 mL per 100 mL; fluorescent baths run 0.1 to 0.4 mL. Contamination or a separated layer in the tube would also call for a new bath.
5. A UV-A meter reads 800 µW/cm² at the inspection surface after the lamp has warmed up. The procedure follows ASME Section V Article 7. What should be done?
Answer: Stop until at least 1,000 µW/cm² is restored. Article 7 requires at least 1,000 µW/cm² of UV-A at the examination surface for fluorescent particles. Move the lamp closer, clean or replace the filter or bulb, then measure again. Longer dark adaptation or more particles do not make up for low UV-A intensity.
6. A switchable yoke lifts 25 lb on DC and 12 lb on AC at the pole spacing to be used. Under ASME Section V Article 7, which modes may be used?
Answer: AC only. Article 7 requires an AC yoke to lift at least 10 lb and a DC or permanent-magnet yoke at least 40 lb at the maximum pole spacing used. The 12 lb AC result passes; the 25 lb DC result fails. The DC mode cannot be used until it passes a lift check.
7. A 12 in long, 2 in diameter part is placed in a 5-turn coil with a high fill factor. Using NI = 35,000 ÷ (L/D + 2), what current is needed?
Answer: About 875 A. L/D = 12 / 2 = 6, so NI = 35,000 / (6 + 2) = 4,375 ampere-turns. Dividing by 5 turns gives about 875 A. Forgetting to divide by the turns gives 4,375 A, and using the low fill-factor formula 45,000 / (L/D) gives 1,500 A.
8. A specification forbids prods on quenched and tempered high-strength steel plate and calls for a yoke instead. What is the main reason?
Answer: Prod arcing can cause hard spots and cracks. Prods pass current through the part, and poor contact can arc or overheat the surface, leaving hard, brittle spots that may crack. Yokes do not pass current through the part, so they avoid arc strikes. Prods produce a circular field around each contact, and DC prods penetrate better than a yoke.
9. A shaft was circularly magnetized with a head shot. A field indicator near its surface reads almost zero, but the shaft still holds a residual field. What is the usual way to demagnetize it?
Answer: Magnetize it longitudinally, then demagnetize that field. A circular field can be fully contained in the part, so little leaks out to the indicator. Converting it to a longitudinal field at a higher level than the circular one gives an external field that can be removed with a demagnetizing coil and measured. Heating only removes magnetism above the Curie point, about 1,418°F (770°C).
10. A forged steel part was quenched after heat treatment. MT shows sharp, jagged, often branching lines at a sharp internal corner and at an abrupt change in section. What are these most likely to be?
Answer: Quench cracks. Quench cracks form from thermal stress during rapid cooling, typically at sharp corners and section changes, and give sharp, jagged, often branching indications. Laps and seams follow the material flow and lie at a shallow angle to the surface; inclusions give short, intermittent lines along the grain.
11. A fillet weld joins a carbon steel plate to an austenitic stainless steel stiffener. MT shows a fuzzy, broad line along the fusion boundary that reappears in the same place after demagnetizing and reprocessing. What should be done?
Answer: Treat it as possibly nonrelevant and confirm with PT. A sharp change in permeability at the boundary with nonmagnetic austenitic steel causes flux leakage, giving a fuzzy line that repeats in the same place. Confirm with a method that does not depend on magnetism, such as PT, before calling it relevant. Raising the current only builds up more particles there.
12. Under ASME Section VIII Division 1 Appendix 6, four rounded indications, each about 3/32 in across, lie in a line with about 1/32 in between their edges. How are they dispositioned?
Answer: Reject, as four or more rounded in a line, 1/16 in or less apart. Appendix 6 rejects relevant linear indications, rounded indications over 3/16 in, and four or more rounded indications in a line separated by 1/16 in or less edge to edge. Each is small, but together they fail the alignment rule. Indications over 1/16 in are relevant, not automatically rejectable.
13. Before a fluorescent MT job, a technician finds that the UV-A lamp's filter is cracked. What should be done under normal safety protocols?
Answer: Remove the lamp from service until the filter is replaced. A cracked or missing filter lets visible light and harmful shorter-wavelength ultraviolet through, which risks eye and skin injury and also raises background light. The lamp must be taken out of service until the filter is replaced. Clear glasses or short exposure times do not make it safe.
14. After an ASTM E1444 examination of an aerospace part, a field indicator reads 5 G at the part surface. The drawing and contract do not set a limit. What is required?
Answer: Demagnetize again until it reads no more than 3 G. Unless otherwise specified, ASTM E1444 requires the residual field to be no more than 3 G (0.3 mT) after demagnetization. Residual fields attract chips, affect instruments and can interfere with welding or machining, so the part is demagnetized again and rechecked.
15. During a pressure vessel shop audit, a bench unit's ammeter calibration record is 16 months old. The procedure follows ASME Section V Article 7. What is the finding?
Answer: Overdue: Article 7 requires calibration at least yearly. Article 7 requires the ammeter of magnetizing equipment to be calibrated at least once a year, or whenever the equipment has had major repair or periodic overhaul. A lift test applies to yokes, not to bench units. Exams done since the calibration lapsed should be reviewed.

Get the full ASNT NDT Level II MT prep

Most popular · cancel anytime

Premium Monthly

$147/month
per exam
About $4.83 a day · less than a retake fee, for the certification that lets you approve procedures and certify technicians
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.

Best value · 3 months free

Premium Yearly

$1,323/year
per exam
Pay for 9 months, get 12. Save $441 against paying monthly.
  • One ASNT Level III exam of your choice: Basic, UT, RT or MT
  • 3,000 practice questions + 6 full mock exams per exam
  • 800 flashcards + 60 key notes per exam, by topic, plus mind maps
  • Spaced repetition + mistakes bank
  • Readiness Score & detailed reports
  • Video lessons as they release
  • Content updates during your access
  • 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
  • Pass Guarantee: complete the prep, pass or 100% back

Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.

Pass Guarantee. Complete the full prep, sit your exam within 60 days, and if you don't pass we refund 100% of your subscription payments. See the requirements
Secure checkout by Stripe Card, Apple Pay, Google Pay Pass Guarantee

ASNT NDT Level II MT exam FAQ

How many questions are on the ASNT NDT Level II MT exam?

Two multiple-choice exams: General 50 items and Specific 40 items (general industry or pressure equipment sector), with a time limit of general 2 hours; specific 2 hours (4 hours in total). Format: computer-based multiple choice with an on-screen calculator. asnt does not publish whether any reference is supplied during these exams; confirm with asnt. this prep covers only the written general and specific exams, not the employer's visual acuity, practical or job-specific exams.

What is the passing score for ASNT NDT Level II MT?

Not published by ASNT for this exam. ASNT says its criterion-referenced cut scores are typically 70% to 80%. Both the General and the Specific exam must be passed, so aim for 80% or higher on each in practice.

How much does the ASNT NDT Level II MT exam cost?

US$740 for ASNT members, US$820 for nonmembers (General plus one Specific exam). Retake of a failed exam or an added sector exam: US$370 / US$410. ASNT fees differ for members and nonmembers and can change, so confirm on the ASNT certification website before you apply.

Which languages is the ASNT NDT Level II MT exam offered in?

US English (ASNT offers an online NDT terminology dictionary in Korean, Mandarin, Spanish, UK English and Arabic).

Where do I take the ASNT NDT Level II MT exam?

Pearson VUE test centers and ASNT Authorized Exam Centers (in person, computer-based, no walk-ins).

Is this ASNT NDT Level II MT practice test free?

Yes. The 15-question practice test on this page is free, with an explanation for every answer and no signup. A free account also unlocks the complete study notes for the first topic. The full ASNT NDT Level II MT prep is Premium at $147 a month for this exam.

What's in the premium ASNT NDT Level II MT prep?

3,000 practice questions organized topic by topic (MT Principles and Theory: 450; Use and Care of MT Equipment and Accessories: 425; MT Techniques and Demagnetization: 425; Interpreting, Evaluating and Documenting Results: 425; Codes, Standards, Specifications and Procedures: 425; Specific Exam: General Industry: 425; Specific Exam: Pressure Equipment: 425), 6 full-length timed mock exams of 50 questions, 800 flashcards and 60 comprehensive key notes split across all 7 topics, plus a mistakes bank and the Readiness Score.

Related practice tests

Exam details are summarized from the official candidate information available in October 2026. ASNT changes formats and fees, so confirm with ASNT Certification Services LLC (American Society for Nondestructive Testing) before you book. NDTLevel3Exam is not affiliated with ASNT or Pearson VUE.

Start the free test