PCN Level 3 (PCN24/GEN) Exam Study Guide (2026)
Everything the PCN Level 3 (PCN24/GEN and method appendices) tests, topic by topic: what each section covers, the facts that come up most, and how to study it. Pair it with the free 15-question practice test.
The exam at a glance
| Questions | Basic: at least 100 multiple-choice questions (Part A 30, Part B 10, Part C 60 made up of 15 for each of four methods). Main method: Part D 30 and Part E 20 multiple-choice questions, plus Part F drafting of one or more NDT procedures |
|---|---|
| Time | PCN24/GEN Issue 4 sets 3 minutes per question for the basic exam (100 questions, 5 hours), 90 minutes for Part D, 60 minutes for Part E and 6 hours for Part F. PCN24/GEN/APP/UT Issue 3 gives 2 minutes per question for Parts A, C and D, 3 minutes for Parts B and E, and recommends 4 hours per Part F procedure. These differ, so confirm the time with your AQB |
| Passing score | 70% in each examination part (A, B, C, D, E and F), with no averaging between parts. The former distinction grade was removed under PCN24. The basic exam must be passed before Part D onward is graded |
| Format | Parts A to D are multiple choice with no outside material (candidates may hold only what the centre provides). Part E may be open book for codes, standards and specifications. For Part F the applicable codes are provided. This prep covers only the multiple-choice knowledge parts and background for Part F. It does not cover drafting assessment or the Level 2 practical required of candidates without current Level 2 certification |
| Certifying body | British Institute of Non-Destructive Testing (BINDT), Certification Services (PCN scheme) |
| Test provider | BINDT or BINDT Authorised Qualifying Bodies and examination centres (paper-based or e-assessment, invigilated). Availability is listed in PCN24/PSL04 |
Mind map: the whole exam on one screen
Read the complete PCN Level 3 (PCN24/GEN) study notes for “Part A: Materials and Product Technology”
Our first full set of comprehensive notes, about 18 minutes of reading: Steels and microstructure · Welding discontinuities · Casting discontinuities · Wrought and in-service discontinuities, a worked exam example, the traps examiners use and a one-minute recap. Create a free account to read it and see how premium notes work before you decide.
1. Part A: Materials and Product Technology
Basic examination Part A: 30 multiple-choice questions, 30% of the 100-question basic exam, on materials technology and science and typical defects in a wide range of products, including castings, welds and wrought products. Pass mark 70%.
Key facts
- Hydrogen (cold) cracking needs hydrogen, a susceptible microstructure and tensile stress, at temperatures below about 200 degrees C. Preheat, low-hydrogen consumables and delayed NDT reduce the risk.
- IIW carbon equivalent: CE = C + Mn/6 + (Cr+Mo+V)/5 + (Ni+Cu)/15. Higher CE means greater hardenability and greater risk of cold cracking.
- Solidification (hot) cracks form along the weld centreline, and are promoted by sulphur, phosphorus and high depth-to-width ratios.
- Lamellar tearing forms in the through-thickness direction of plate, under high restraint, in steel with low through-thickness ductility.
- Casting discontinuities: shrinkage, gas porosity, cold shuts, hot tears, inclusions and misruns.
- Wrought discontinuities: laminations (rolling), laps (forging or rolling), seams and forging bursts.
- In-service: fatigue, creep, stress corrosion cracking, corrosion and erosion.
- Heat treatment: annealing softens, normalising refines grain, hardening and tempering raise strength, and stress relief reduces residual stress.
Flashcards
Exam tip: Ask when and where a flaw formed. Timing and location usually separate hot cracking, cold cracking and lamellar tearing.
2. Part B: PCN24 Qualification and Certification
Basic examination Part B: 10 multiple-choice questions on the qualification and certification procedure in PCN24/GEN, which is based on BS EN ISO 9712:2022. Pass mark 70%, so a score of 6 out of 10 fails the part.
Key facts
- Level 3 may establish and validate instructions and procedures, interpret codes and standards, designate methods and techniques, and assume full responsibility for a test facility.
- Basic training for direct access totals 12 days: Part A 3 days, Part B 1 day, Part C 8 days. Method Level 3 training: RT 5, UT 5, MT 4, PT 3, VT 3, ET 6 days.
- Level 3 experience with Level 2: 450 days for ET, ACFM, RT, UT, TT and 240 days for MT, PT, VT (Table 3).
- Vision: near acuity to Jaeger 1 or Times Roman N4.5 at not less than 30 cm, annually; colour vision test within the previous five years.
- Re-examination: maximum two re-exams of failed elements, no sooner than 30 days and within one year of the original examination, or 7 days after supplementary training.
- The basic exam result remains valid if the first main method exam is passed within five years.
- Certificates are normally valid for five years. Level 3 renewal or recertification may be by examination or structured credit, with proof of continued practical competence.
- Cheating results in exclusion from PCN examinations for at least one year.
Flashcards
Exam tip: With 10 questions, one mistake is 10 percent. Read PCN24/GEN through carefully, because small numbers decide this part.
3. Part C: Volumetric Methods at Level 2 Standard (UT and RT)
Basic examination Part C: 60 multiple-choice questions at Level 2 standard, 15 for each of four methods chosen by the candidate, including at least one volumetric method (UT or RT). Pass mark 70%. PCN24/GEN Appendix Z1 sets the syllabus.
Key facts
- UT: velocity = frequency x wavelength; steel velocities are about 5,960 m/s compression and 3,240 m/s shear.
- Full skip distance = 2 x thickness x tan(angle); half skip is half of this.
- UT detects planar flaws best when the beam meets them near perpendicular; TOFD and phased array are advanced techniques.
- RT: geometric unsharpness Ug = source size x object-to-film / source-to-object.
- Exposure changes with distance squared and is proportional to source strength multiplied by time.
- RT shows volumetric flaws well; tight planar flaws at an angle to the beam are often missed.
- Image quality indicators (IQIs) confirm the sensitivity of the radiograph.
- RT candidates must hold valid radiation safety certification recognised by BINDT.
Flashcards
Exam tip: Choose methods where you can do the arithmetic fast. UT and RT questions in Part C are often solved with one formula.
Test yourself on these topics
Take the free 15-question PCN Level 3 (PCN24/GEN) test, then save your results to unlock your Readiness Score and the mistakes bank.
4. Part C: Surface and Electromagnetic Methods (MT, PT, VT, ET)
Basic examination Part C: the other 15-question blocks at Level 2 standard if chosen by the candidate, within the 60-question Part C. Pass mark 70%. Syllabi are in PCN24/GEN Appendix Z1.
Key facts
- MT detects surface and slightly sub-surface discontinuities in ferromagnetic materials.
- Flux leakage is strongest when the discontinuity is across the field. A coil gives a longitudinal field, a threading bar gives a circular field.
Flashcards
Exam tip: If you take these methods, learn the viewing condition numbers. They are the easiest marks to lose.
5. Part D: Level 3 Method Knowledge
Main method examination Part D: 30 multiple-choice questions on Level 3 knowledge of the certified method, 2 minutes per question in the UT appendix and 90 minutes in PCN24/GEN. Pass mark 70%. A holder of Level 3 in the same method and another sector is exempt.
Key facts
- UT: near-field length N = D squared / (4 x wavelength); the beam diverges beyond the near field.
- Snell's law: sin(angle 1) / velocity 1 = sin(angle 2) / velocity 2.
Flashcards
Exam tip: Convert units before you calculate. Most wrong answers come from mixing metres, millimetres and hertz.
6. Part E: Codes, Standards and Sector Application
Main method examination Part E: 20 multiple-choice questions on application of the method in the sector concerned, including applicable codes, standards and specifications. Pass mark 70%. It may be open book for codes, standards and specifications.
Key facts
- Personnel qualification: BS EN ISO 9712:2022.
- Weld NDT general rules: BS EN ISO 17635.
Flashcards
Exam tip: Even if Part E is open book, tabbing the standards you expect will save time. Know which number covers technique and which covers acceptance.
7. Part F: NDT Procedure Drafting
Main method examination Part F: drafting of one or more NDT procedures in the relevant sector, with the applicable codes available. Pass mark 70%. Candidates who have already passed a drafted procedure may have critical analysis of an existing procedure in its place. This course gives background only, not assessed drafting.
Key facts
- A procedure sets out the method, scope, responsibilities, equipment, technique and reporting, and is written so that a qualified person can repeat the test.
- A Level 2 NDT instruction is derived from the procedure for specific application.
Flashcards
Exam tip: In a critical review, ask whether an independent operator could reproduce the test from the page alone.
How to pass
- Part C is the largest part, at 60 questions from four methods you choose. At least one must be volumetric (UT or RT), so choose the methods you know best and check them with your AQB.
- Each part is graded separately at 70%. A strong average cannot rescue a weak Part B, and Part B has only 10 questions, so memorise PCN24/GEN.
- BINDT's own documents differ on timing. Confirm minutes per question and Part F time with your AQB, and practise at the shorter allowance.
- Passing the basic exam stays valid only if your first main method examination is passed within five years, so plan your Parts D, E and F early.
Frequently asked questions
How long should I study for the PCN Level 3 (PCN24/GEN) exam?
Most working candidates need 4 to 8 weeks at 45 to 60 minutes a day. Book your exam once your Readiness Score has stayed at 80 or higher for about a week.
Can I take the PCN Level 3 (PCN24/GEN) exam online?
No. ASNT NDT Level III exams are taken in person, on a computer, at Pearson VUE test centers or ASNT Authorized Exam Centers. Format: parts a to d are multiple choice with no outside material (candidates may hold only what the centre provides). part e may be open book for codes, standards and specifications. for part f the applicable codes are provided. this prep covers only the multiple-choice knowledge parts and background for part f. it does not cover drafting assessment or the level 2 practical required of candidates without current level 2 certification. Check ASNT's current exam information for the rules.
What score do I need to pass the PCN Level 3 (PCN24/GEN) exam?
70% in each examination part (A, B, C, D, E and F), with no averaging between parts. The former distinction grade was removed under PCN24. The basic exam must be passed before Part D onward is graded. The exam has basic: at least 100 multiple-choice questions (part a 30, part b 10, part c 60 made up of 15 for each of four methods). main method: part d 30 and part e 20 multiple-choice questions, plus part f drafting of one or more ndt procedures and a time limit of pcn24/gen issue 4 sets 3 minutes per question for the basic exam (100 questions, 5 hours), 90 minutes for part d, 60 minutes for part e and 6 hours for part f. pcn24/gen/app/ut issue 3 gives 2 minutes per question for parts a, c and d, 3 minutes for parts b and e, and recommends 4 hours per part f procedure. these differ, so confirm the time with your aqb.
What are the most tested topics?
The outline covers part a: materials and product technology, part b: pcn24 qualification and certification, part c: volumetric methods at level 2 standard (ut and rt), part c: surface and electromagnetic methods (mt, pt, vt, et), part d: level 3 method knowledge, part e: codes, standards and sector application, part f: ndt procedure drafting. Use the free practice test to see which ones you need most.
The premium PCN Level 3 (PCN24/GEN) study path
Premium PCN Level 3 (PCN24/GEN) prep is studied one topic at a time. Each step starts with that topic's key notes and flashcard deck, then its own question sets of 25, so you master one topic before you move to the next. When every topic is strong, the 6 full mock exams show you're ready.
Your step-by-step study path
- 1Part A: Materials and Product Technology9 key notes, 115 flashcards, then 450 practice questions in 18 sets of 25Notes free with an account
- 2Part B: PCN24 Qualification and Certification9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25Premium
- 3Part C: Volumetric Methods at Level 2 Standard (UT and RT)9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25Premium
- 4Part C: Surface and Electromagnetic Methods (MT, PT, VT, ET)9 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25Premium
- 5Part D: Level 3 Method Knowledge8 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25Premium
- 6Part E: Codes, Standards and Sector Application8 key notes, 115 flashcards, then 425 practice questions in 17 sets of 25Premium
- 7Part F: NDT Procedure Drafting8 key notes, 110 flashcards, then 425 practice questions in 17 sets of 25Premium
- Final step: 6 full mock exams100 questions each, timed like test day. Pass them, then book your exam.Premium
Get every note, flashcard and question
Premium Monthly
- One ASNT Level III exam of your choice: Basic, UT, RT or MT
- 3,000 practice questions + 6 full mock exams per exam
- 800 flashcards + 60 key notes per exam, by topic, plus mind maps
- Spaced repetition + mistakes bank
- Readiness Score & detailed reports
- Video lessons as they release
- Content updates during your access
- 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
- Pass Guarantee: complete the prep, pass or 100% back
Renews monthly until you cancel. Cancel in two clicks from your account; you keep access until the end of the month you've paid for. No minimum term.
Premium Yearly
- One ASNT Level III exam of your choice: Basic, UT, RT or MT
- 3,000 practice questions + 6 full mock exams per exam
- 800 flashcards + 60 key notes per exam, by topic, plus mind maps
- Spaced repetition + mistakes bank
- Readiness Score & detailed reports
- Video lessons as they release
- Content updates during your access
- 5 bonuses: NDT formula sheet, discontinuity atlas, study planner and more
- Pass Guarantee: complete the prep, pass or 100% back
Renews once a year until you cancel. We email you before each renewal. Cancel any time from your account; you keep access until the end of the year you've paid for.
Summarized from ASNT's official candidate information and the rules cited, checked October 2026. Confirm current requirements with British Institute of Non-Destructive Testing (BINDT), Certification Services (PCN scheme).